Bedienungsanleitung Parkside PKS 1500 A1 - IAN 270413 (Seite 13 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

706375

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

8 GB/IE

lease the handle (2) after completing the cut; instead

allow the machine head to move upwards slowly whilst

applying light counter pressure.

Mitre cut 0°- 45° (Fig. 1, 1.3)

The crosscut saw can be used to make mitre cuts of

0° - 45° in relation to the work face.

Important. To make miter cuts (inclined saw head), the

adjustable stop rail (27a) must be xed at the outer

position.

• Open the set screw (27b) for the adjustable stop rail

(27a) with an Allen key and push the adjustable stop

rail outwards.

• The adjustable stop rail (27a) must be xed far enough

in front of the innermost position that the distance

between the stop rail (27a) and the saw blade (5)

amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (27a) and

the saw blade (5) cannot collide.

• Secure the locking lever (27b) again.

• Move the machine head to the top position.

• Fix the rotary table (9) in the 0° position.

• Loosen the set screw (23) and use the handle (2) to

angle the machine head to the left, until the pointer

(25) indicates the desired angle measurement on the

scale (24).

• Re-tighten the xing screw (23).

• Cut as described in section “Cross-cutting”.

Saw blade replacement (Fig. 5)

• Pull out the mains plug.

• Place the saw unit in „cross-cutting“ position

• Unlock the moving saw blade guard (6) by pressing

the lock (3 - Fig. 1); in the process, raise the saw bla-

de guard so that the saw blade is free.

• Actuate the spindle lock (22 - Fig. 3).

• Loosen the saw blade fastening screw (28) - (Atten-

tion: left-handed thread).

• Remove the screw (28) and saw blade ange (29).

• Carefully remove the saw blade (risk of injury from the

saw blade teeth).

• Place a new saw blade on the inner saw blade an-

ge. In the process, observe the rotational direction of

the saw blade.

• Fit the outer saw blade ange and rmly tighten the

screw.

• Move the saw blade guard back to the correct position.

Replacing laser batteries (Fig. 6)

• Remove the laser battery cover (30). Remove the 2

batteries.

• Replace both batteries with the same or an equivalent

type. Make sure that they are inserted with the same

polarity as the used batteries.

• Close the battery cover.

Switch ON / switch OFF the laser (Fig. 6)

To switch on: Move the ON/OFF switch (33) of the la-

ser (34) to the “1” position. A laser line is projected on-

to the material you wish to process, providing an exact

guide for the cut.

To switch off: Move the ON/OFF switch of the laser to

the “0” position.

Adjusting the laser (Fig. 7)

If the laser (31) ceases to indicate the correct cutting

line, you can readjust the laser. To do so, open the

screws (32) and set the laser by moving sideways to

that the laser beam strikes the teeth of the saw blade

(5).

m Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

Important information

In the event of an overloading the motor will switch its-

elf off. After a cool-down period (time varies) the motor

can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been impro-

perly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage re-

gularly. Make sure that the connection cable does not

hang on the power network during the inspection.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H 07 RN“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm2.

Connections and repairs of electrical equipment

may only be carried out by an electrician.

Please provide the following information in the event of

any enquiries:

• Type of current for the motor

• Machine data - type plate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKS 1500 A1 - IAN 270413 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info