706359

Parkside PKS 1500 B3 - IAN 327261 1904 Seite 15

15
Zoom out
Zoom in
Vorherige Seite
1/100
Nächste Seite
10 GB/IE/NI
9.5 Precision adjustment of the stop for mitre cut
45° (fig. 1/2/3/6/7/8)
• No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (25).
• Fix the rotary table (13) in the 0° position.
Important. For mitre cuts, the adjustable stop rail (8a) must
be fixed at the inner position.
• Open the set screw (8b) for the moveable stop rail (8a) and
push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (8a) and the saw blade (6) amounts to a maximum
of 8 mm.
• Before making a cut, check that the stop rail (8a) and the
saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Loosen the locking screw (23) and use the handle (3) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (B) between the saw blade (6) and
rotary table (13).
• Loosen the locknut (22a) and adjust the adjustment screw
(22) until the angle between the saw blade (6) and the ro-
tary table (13) is precisely 45°.
• Re-tighten the locknut (22a).
• Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (28) using a Philips screwdriv-
er, set to position 45° on the angle scale (27) and re-tighten
the retaining screw.
9.6 Mitre cut 0°- 45° and turntable 0° (fig. 1/2/3/6)
The cross cut mitre saw can be used to make mitre cuts of 0° -
45° in relation to the work face.
Important. For mitre cuts, the adjustable stop rail
(8a) must be fixed at the inner position.
• Open the set screw (8b) for the moveable stop rail (8a) and
push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (8a) and the saw blade (6) amounts to a maximum
of 8 mm.
• Before making a cut, check that the stop rail (8a) and the
saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (13) in the 0° position.
• Loosen the locking screw (23) and use the handle (3) to
angle the machine head (4) to the left, until the pointer (28)
indicates the desired angle measurement on the scale (27).
• Re-tighten the locking screw (23).
• Cut as described in section 9.3.
9.7 Mitre cut 0°- 45° and turntable 0°- 45°
(fig. 1/2/3/6)
The cross cut mitre saw can be used to make mitre cuts to the
left of 0°- 45° in relation to the work face and, at the same
time, 0° - 45° to the left or 0° - 45° to the right in relation to
the stop rail (double mitre cut).
Attention! For mitre cuts (inclined saw head), the
moveable stop rail (8a) must be fixed in the outer
position.
• Open the set screw (8b) for the moveable stop rail (8a) and
push the moveable stop rail (8a) outwards.
• The adjustable stop rail (8a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (8a) and the saw blade (6) amounts to a maximum
of 8 mm.
• Before making a cut, check that the stop rail (8a) and the
saw blade (6) cannot collide.
• Secure the set screw (8b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (13) by loosening the set screw (7).
• Using the handle (3), set the rotary table (13) to the desired
angle.
• Retighten the set screw (7) in order to secure the rotary table.
• Undo the locking screw (23).
• Use the handle (3) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 9.6).
• Re-tighten the locking screw (23).
• Cut as described under section 9.3.
9.8 Limiting the cutting depth (fig. 3)
• The cutting depth can be infinitely adjusted using the screw
(24). To do this loosen the locknut (24a) on the screw (24).
Turn the screw (24) in or out to set the required cutting depth.
Then re-tighten the locknut (24a) on the screw (24).
• Check the setting by completing a test cut.
9.9 Changing the saw blade (fig. 1/2/3/9/10)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
• Swing the machine head (4) upwards and secure with the
stop for cutting depth limiting (25).
• Fold the saw blade guard (5) upwards until the saw blade
guard (5) is above the flange screw (29).
• With one hand insert the Allen key (C) in the flange screw
(29).
• Hold the Allen key (C) and slowly close the saw blade guard
(5) until it touches the Allen key (C).
• Firmly press the saw shaft lock (32) and slowly rotate the
flange screw (29) in clockwise direction. The saw shaft lock
(32) engages after no more than one rotation.
• Now, using a little more force, slacken the flange screw (29)
in the clockwise direction.
• Turn the flange screw (29) right out and remove the outer
flange (30).
• Take the blade (6) off the inner flange and pull out down-
wards.
• Carefully clean the flange screw (29), outer flange (30) and
inner flange.
• Fit and fasten the new saw blade (6) in reverse order.
• Important! The cutting angle of the teeth, in other words the
direction of rotation of the saw blade (6) must coincide with
the direction of the arrow on the housing.
• Before continuing your work make sure that all safety de-
vices are in good working condition.
… 15 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

parkside-pks-1500-b3---ian-327261-1904

Suche zurücksetzen

  • Am Maschinenkopf befindet sich an der Frontseite ein Knopf zum reindrücken mit Feder. Wofür ist dieser? Eingereicht am 4-5-2020 18:59

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PKS 1500 B3 - IAN 327261 1904 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info