Bedienungsanleitung Parkside PKS 1500 B3 - IAN 346110 (Seite 13 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

779274

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

8GB/IE/NI

7. Technical data

AC motor.....................................................220 - 240 V~ 50Hz

Power S1 .....................................................................1200 Watt

Operating mode ............................................ S6 25%* 1500W

Idle speed n0 ..............................................................5000 min-1

Carbide saw blade ...............................ø 210 x ø 30 x 2,6 mm

Number of teeth .......................................................................48

Maximum saw blade tooth width ......................................3 mm

Swivel range ................................................... -45° / 0°/ +45°

Mitre cut ........................................................ 0° - 45° to the left

Saw width at 90° ................................................. 120 x 60 mm

Saw width at 45° ....................................................80 x 60 mm

Saw width at 2 x 45°

(double mitre cut) .....................................................80 x 35 mm

Protection class .................................................................... II /

Weight ......................................................................... ca. 7,6 kg

Laser class ...................................................................................2

Wavelength of laser ........................................................650 nm

Laser output .....................................................................< 1 mW

* S6, continuous operation periodic duty. Identical duty cycles

with a period at load followed by a period at no load. Running

time 10 minutes; duty cycle is 25% of the running time.

The work piece must have a minimum height of 3

mm and a minimum width of 10 mm.

Make sure that the workpiece is always secured

with the clamping device.

Noise

Total noise values determined in accordance with EN 62841.

Sound pressure level LpA ............................................ 99,6 dB(A)

Uncertainty KpA ......................................................................3 dB

Sound power level LWA ............................................ 112,6 dB(A)

Uncertainty KWA .....................................................................3 dB

Wear hearing protection.

The eﬀects of noise can cause a loss of hearing

The above-mentioned noise emission values were measured in

accordance with a standardised test procedure and can be

used to compare one power tool with another.

The above-mentioned noise emission values can also be used

for the preliminary assessment of exposure.

Warning:

• The noise emissions during the actual use of the power tool

may diﬀer from the above-mentioned values depending on

the power tool being used, in particular on the type of work-

piece being processed.

• Try to keep emissions as low as possible, for example by

limiting your working time. In this regard, all the operational

cycle phases must be taken into consideration (such as the

times when the tool is switched oﬀ or running idle).

8. Before starting the equipment

• Open the packaging and remove the device carefully.

• Remove the packaging material as well as the packaging

and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for transport damage.

• If possible, store the packaging until the warranty period has

expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, ﬁlm and small parts! There is a risk of swal-

lowing and suﬀocation!

Always ensure that the machine is stable and can

stand securely, i. e. bolted down on a workbench.

• The equipment must be set up where it can stand securely.

Secure the machine on a workbench or a base frame with 4

screws (not included in delivery) using the holes on the ﬁxed

saw table (9).

• All covers and safety devices have to be properly ﬁtted be-

fore the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed before,

watch out for foreign bodies such as nails or screws, etc.

• Before you press the ON/OFF switch check that the saw

blade is ﬁtted correctly. Moving parts must run smoothly.

• Before you connect the equipment to the power supply make

sure the data on the rating plate are identical to the mains

data.

8.1 Assembling the work piece clamping device

(ﬁg. 2)

• Loosen the locking screw (19) and attach the work piece

clamping device (15) to the left or right of the ﬁxed saw

bench.

• Afterwards, retighten the locking screws (19).

8.2 Assembling the work piece supports

(ﬁg. 2 - 3)

• Loosen the locking screw (14) and guide the work piece

support through the speciﬁed hole on the side of the ﬁxed

saw bench.

• Make sure that the work piece support (18) is also guided

through the two plates on the underneath.

• Afterwards, retighten the locking screw (14).

• Repeat this process on the other side.

8.3 Assembling the support stand (ﬁg. 2 - 3)

• Loosen the locking screw (20) on the underneath of the saw

and guide the support stand (21) through the speciﬁed holes

on the back of the saw.

• Afterwards, retighten the locking screw (20).

Parkside PKS 1500 B3 - IAN 346110 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info