Bedienungsanleitung Parkside PKSA 20-Li A1 - IAN 327523-1904 (Seite 45 von 193) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

722811

Zoom out

Zoom in

Vorherige Seite

1/193

Nächste Seite

PKSA 20-Li A1

│

39 ■

■ Do not drop the chainsaw, knock it against ob-

structions and do not use the guide rail as a lever.

■ Use the chainsaw only for sawing wood.

■ When sawing a branch that is under tension, be

prepared for it to spring back. Once the tension

in the wooden ﬁbres is released, the branch can

hit the operator and/or knock the chainsaw out

of his hands.

■ Be extremely careful when cutting brushwood

and young trees. The thin material can catch in

the saw chain and ﬂy in your direction or knock

you oﬀ balance.

Charging the battery pack (see ﬁg. A)

CAUTION!

► Always unplug the tool before you remove

the battery pack from or connect the battery

pack to the charger.

NOTE

► Never charge the battery pack at an ambient

temperature of below 10°C or above 40°C.

If a lithium-ion battery is to be stored for an

extended period, the charge level should be

checked regularly. The optimum charge level

is between 50% and 80%. The storage

climate should be cool and dry and the

ambient temperature should be between 0°C

and 50°C.

♦ Connect the battery pack

to the high-speed

battery charger

(see ﬁg. A).

♦ Insert the power plug into the socket.

The charge control LED

lights up red.

♦ The green charge control LED

indicates that

the charging process is complete and the bat-

tery pack is ready for use.

ATTENTION!

♦ If the red charge control LED

ﬂashes, this

means that the battery pack has overheat-

ed and cannot be charged.

♦ If the red and green charge control LEDs

both ﬂash, this means that the battery

pack is defective.

♦ Switch oﬀ the charger for at least 15 minutes

between successive charging sessions. Also

disconnect the power plug from the mains

power socket.

Attaching/disconnecting the battery

pack to/from the tool

Attaching the battery pack:

♦ Push the battery pack

into the handle until

it clicks into place.

Removing the battery pack:

♦ Press the release button

and remove the

battery pack.

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see also main

diagram).

The status/remaining charge will be shown on

the battery display LED

as follows:

♦ RED/ORANGE/GREEN = maximum charge

RED / ORANGE = medium charge

RED = low charge – charge the battery

Adding chain oil

WARNING!

► Always check the chain lubrication before

starting work.

► Never work without chain lubrication!

If the saw chain runs dry, the cutting equip-

ment may become irreparably damaged in a

short time.

NOTE

► Use only saw chain oil, preferably biode-

gradable. Do not use waste oil, motor oil, etc.

► While working, check whether the chain

lubrication is working correctly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKSA 20-Li A1 - IAN 327523-1904 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info