Bedienungsanleitung Parkside PKZ 180 A1 - IAN 93472 (Seite 30 von 34) (Deutsch, Englisch, Holländisch)

668303

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

30 GB

... / Cleaning / Care / Spare ... / Maintenance and ... /Information about ...

General safety information for electrical devices / Before use / Start-up

always use the handle on the device to move

it. Never touch the device itself!

ATTENTION! The compressor housing may

become hot during use. Do not touch hot sur-

faces in order to prevent burns.

Never leave the device in operation unattended.

Built-up heat generated by the device can be a

source of danger. This compressor is equipped

with overheat protection. Of the motor reaches

a temperature of 130 °C, the overheat protec-

tion will automatically shut it oﬀ. This allows the

motor to cool oﬀ, thus preventing damage. Once

the motor has cooled down, it will automatically

restart. This pause is normal and is intended to

protect the motor. This process will repeat if the

motor again reaches a temperature of 130 °C.

Only use indoors.

WARNING! The compressor can start up

without warning!

Before use

Only use the compressor in dry, well ventilated

rooms. The room must be free from dust, acids,

fumes, explosive or ﬂammable gasses.

Check that all of the device‘s parts are in per-

fect condition.

Make sure that the available mains voltage is

compatible with the voltage intended for oper-

ating the compressor.

Avoid long supply lines.

Place the compressor on its rubber feet before

use.

Note: The switch light indicates the mains connec-

tion and does not indicate pump operation.

Start-up

Switching the compress

on / oﬀ (cf. Fig. A)

Please set the on / oﬀ switch

to position I to

switch on.

Please set the on / oﬀ switch

to position 0

to switch on.

Establishing connections

(cf. Fig. B)

ATTENTION! Switch oﬀ the device for this

purpose. Please hold on to the coupling to

prevent injuries due to the hose rebounding.

Connect the nipple of your air tool to the com-

pressor‘s air hose

To disconnect this connection, pull back on the

quick-disconnect coupling of the air hose

Using the tyre ﬁlling

device (cf. Fig. C)

The compressed air tyre ﬁlling device

is used to

inﬂate car tyres and, used with the appropriate ac-

cessories, also to inﬂate and control bicycle tyres,

rubber dinghies, air mattresses, balls, etc.

ATTENTION! The pressure gauge

is not cali-

brated! Please check the air pressure with a cali-

brated device after ﬁlling.

Using the blow-out gun

(cf. Fig. D)

The tyre ﬁlling device

can also be used to clean

hollow spaces and dirty surfaces and tools when

used as a blow-out gun.

To do so, please ﬁrst remove the hose with

valve adapter

Now attach the blow-out adapter

with the

tyre ﬁlling device

93472_Kompressor_PKZ_180_A1_Content_DE-AT-NL.indd 30 13.11.13 16:56

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKZ 180 A1 - IAN 93472 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PKZ 180 A1 - IAN 93472

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info