Bedienungsanleitung Parkside PMBS 105 A1 - IAN 115751 (Seite 6 von 33) (Deutsch, Englisch, Holländisch)

607541

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

6 GB/IE

Introduction / General power tool safety warningsIntroduction

Modelling belt sander PMBS 105 A1

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product.

The instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as descri-

bed and for the speciﬁed applications. If you pass

the product on to anyone else, please ensure that

you also pass on all the documentation with it.

Intended use

The belt sander is designed for model making, tool-

ing and shaping. However, it is also suitable for small

car repairs, e.g. bodywork. The tool can also be

used for deburring, rough machining, ﬁnish grinding,

edge breaking, paint removal, rust removal and

sharpening tools, as well as working on metal, non-

ferrous metals, wood and plastic. The device is not

intended for commercial use. Any other uses, and /

or modiﬁcations to the tool are considered improper

use and may result in serious hazards. The manufac-

turer is not liable for damage caused by improper us

Features

ON / OFF switch

Connection cable with mains plug

Connection socket

Slide for tensioner

Tensioner

Adjusting knob

Extraction adapter

Dust extractor hose

Screw clamp

Belt support

Abrasive belt

Drive roller

Notch

Scope of delivery

1 Modelling belt sander PMBS 105 A1

1 Abrasive belt (installed)

1 Extraction adapter (for external dust collection)

1 Dust extractor hose

1 Screw clamp

1 Set of instructions for use

Technical Data

Modelling belt sander PMBS 105 A1

Rated voltage: 230 V∼ 50 Hz

Operating mode:

Short term use: S2 10 min

Note: After a continuous operating time of 10

minutes, a rest period is enabled, until the device has

cooled to a temperature within 2 K (2 °C) of the

room temperature.

Rated power input: 105 W

Idle belt -

speed: 170 m / min

Idle speed: n

640 min

-1

Abrasive belt: 40 x 265 mm

Grinding surface: 60 x 40 mm

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 81.20 dB(A)

Sound power level: 92.20 dB(A)

Uncertainty K: 3 dB

Vibration- and noise reduction

To minimise the impact of vibration and noise, limit

the work time, use the settings for lower vibration-

and noise emission, and wear personal protective

equipment.

Please observe the following points to minimise the

vibration- and noise emission:

1. Only use the product properly in accordance

with the design and the instructions.

2. Ensure the product is in good working order and

well maintained.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PMBS 105 A1 - IAN 115751 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PMBS 105 A1 - IAN 115751

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info