763020
8
Zoom out
Zoom in
Vorherige Seite
1/49
Nächste Seite
8GB/IE/NI
Use the product only as described and only
for the specific applications as stated. Keep
these instructions in a safe place. Ensure you
hand over all documentation when passing
the product on to anyone else. Any use that
differs to the intended use as stated above is
prohibited and potentially dangerous.
Damage or injury caused by misuse or
disregarding the above warning is not
covered by the warranty or any liability on
the part of the manufacturer. The device
is not intended for commercial use.
Commercial use will void the guarantee.
RESIDUAL RISK
Even if you operate the device as intended,
there will be residual risks.
Following hazards may occur in conjunction
with the construction and design of this
plasma cutter:
Eye injuries due to glare,
Touching hot parts of the device or
workpiece (burn injury),
In case of improper protection risk of
accident and fire through sparks and
slag particles,
Harmful emissions from smoke and gases
if there is a lack of air or if closed rooms
are insufficiently extracted.
Reduce the residual risk by carefully using
the device as intended and observing all
instruction.
• Package contents
1 plasma cutter
1 ground cable with terminal
1 cutting cable incl. cutting torch
1 compressed air hose with Quick-Connect
2 hose clamps
3 electrodes (1 pre-assembled)
1 set of operating instructions
3 burner sleeves (1 pre-assembled)
1 Removable roller guide
• Parts description
PLEASE NOTE!
f After unpacking the product, please
check that all of the package contents
are present and that the device is in
perfect condition. Do not use the device
if it is defective.
1Plasma cutter
2Handle
3Mains plug
4Ground terminal
5Ground terminal plug
6Plasma burner power plug
7Plasma burner plug
8Plasma burner
8a Plasma burner button
8b Nozzle clamping sleeve
8c Burner sleeve
8d Electrode
8e Diffuser
9Overheat protection indicator lamp
10 Plasma burner power socket
11 Ground terminal connection socket
12 Plasma burner connection socket
13 Current controller
14 Mains indicator lamp
15 Quick connector compressed air hose
16 Compressed air hose
Introduction
327358_Plasmaschneider_PPS_40_B2_content_LB6_IE_NI.indb 8 06.09.2019 12:41:02
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PPS 40 B2 - IAN 327358 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info