Bedienungsanleitung Parkside PPS 40 B2 - IAN 327358 (Seite 18 von 49) (Deutsch, Englisch)

763020

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

18 GB/IE/NI

• Using the device

• Operation

1. Set the plasma cutter 1 up in a dry and

well ventilated area.

2. Position the machine in the vicinity of the

workpiece.

3. Press the on/off switch 17.

4. Clamp the ground terminal 4 to the

workpiece to be cut and make sure that

there is a good electrical contact.

5. Set the cutting current on the current

controller 13. If the arc beam is inter-

rupted the cutting current must be set

higher if necessary. If the electrode burns

through frequently, then the cutting

current must be set lower.

6. Position the plasma cutter 8 on the

workpiece so that the burner sleeve 8c is

free and that a blowback of the molten

metal is not possible. Press the plasma

burner button 8a. The transmitted cutting

arch is ignited on the edge of the sheet

in this manner.

7. Start cutting slowly and then increase the

speed in order to achieve the desired

cutting quality.

8. The speed must be regulated so that a

good cutting capacity can be achieved.

The plasma beam creates a straight arch

(stainless steel, aluminium) or a 5° arch

of approach (soft steel).

To cut in the manual cutting mode,

pull the overlying burner across the

workpiece while maintaining a

constant speed. To achieve the perfect cut, it

is important for the material thickness to

comply with the correct cutting speed. If the

cutting speed is too low, the cutting edge will

be blunt due to the severe heat input.

The optimal cutting speed is achieved once

the cutting jet is slightly inclined towards the

rear while cutting. If the plasma burner

button 8a is released, the plasma jet goes

out and the power source switches off. The

gas continues to flow for approx. 5 seconds

in order to cool the burner. The same

process is followed when the workpiece is

pulled out with a pressed plasma burner

button 8a. During the gas post-flow time,

the plasma cutter 1 must not be switched off

to avoid damaging the plasma burner 8 as

a result of overheating.

ATTENTION!

fThe device must be left on for approx.

2-3 minutes once the cutting work has

been completed. The cooler cools the

electronics.

• Types of plasma cutting

Drag cutting

Hold the tip of the burner sleeve

low over

the workpiece and press the plasma burner

button

. Now move the burner sleeve until

there is contact with the workpiece and

the cutting arch is fixed. Once the cutting

arch has been generated, move the plasma

burner

in the desired direction. Makes

sure that burner sleeve is slightly

angled

and that contact with the workpiece is

maintained. This working method is called

drag cutting. Avoid quick movements. A sign

of quick movements is sparks that fall of the

top of the workpiece. Move the plasma

burner at a

speed in which the spark

accumulation is concentrated on the bottom

side of the workpiece. Ensure the material is

completely separated prior to continuing with

this process. Set the necessary drag speed.

Using the device

327358_Plasmaschneider_PPS_40_B2_content_LB6_IE_NI.indb 18 06.09.2019 12:41:02

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PPS 40 B2 - IAN 327358 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info