763020
21
Zoom out
Zoom in
Vorherige Seite
1/49
Nächste Seite
21GB/IE/NI
Troubleshooting / Maintenance and care
Arc stops during
cutting? Cutting speed too low.
Plasma burner 8 is held too
high and too far away from
the material.
Plasma burner component
parts are worn 8b, 8c , 8d, 8e .
Workpiece no longer
connected to the grounding
cable.
Increase the cutting speed until
the problem no longer exists.
Lower the plasma burner 8 to
the recommended height.
Check and replace worn
parts.
Check the connections.
Insufficient
penetration? Cutting speed too fast.
Burner sleeve 8c is not straight
Metal is too thick.
Plasma burner component
parts are worn 8b, 8c , 8d, 8e .
Slow down the working speed
Adjust the inclination.
Several cycles necessary.
Check and replace worn
parts.
Consumables
wear quickly? Performance was over-
stretched.
Arc control time exceeded.
Incorrect plasma burner
assembly.
Insufficient air supply, pressure
too low.
Faulty air compressor.
Material too thick, increase
the angle to avoid material
from being blown back into
the tip.
Do not control the arc for
more than 5 seconds. You can
also start with contact
between the burner sleeve 8c
and metal or with a 3.2 mm
distance to the metal.
Check the air filter, increase
the air pressure.
Check the performance of the
air compressor and make sure
the inlet pressure is at least
100 PSI (6.8 bar).
• Maintenance and care
• Maintaining the burner
The parts displayed in Figure F are the
electrode 8d, diffuser 8e and the burner
sleeve 8c . They can be replaced once
the nozzle clamping sleeve 8b has been
unscrewed.
The electrode 8d must be replaced if
there is a crater of approximately
1.5 mm depth in the centre.
ATTENTION!
fTo unscrew the electrode, do not apply
irregular pressure, gradually increase
pressure until the thread is released.
The new electrode must be screwed into
its bracket and blocked but not tightened
up to the stop.
327358_Plasmaschneider_PPS_40_B2_content_LB6_IE_NI.indb 21 06.09.2019 12:41:03
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PPS 40 B2 - IAN 327358 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info