Bedienungsanleitung Parkside PSBSAP 20-Li B3 - IAN 391011 (Seite 20 von 198) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

796076

Zoom out

Zoom in

Vorherige Seite

1/198

Nächste Seite

PSBSAP 20-Li B3 GB│IE │ 9 ■

In second gear

(speed selector switch6 in position 2),

you can reach a speed of approx. 2000 rpm for

carrying out drilling work.

Operation

Switching on/oﬀ

Turn on

♦ Press and hold the ON/OFF switch8 to start

the tool. The LED work light 0 lights up when

the ON/OFF switch8 is pressed lightly or

fully. This provides illumination of the work

area in poor lighting conditions.

Switching oﬀ

♦ Release the ON/OFF switch8 to switch oﬀ

the tool.

Setting the rotational speed

Pressing the ON/OFF switch8 lightly yields a low

speed. Increasing the pressure increases the speed.

NOTE

► The integrated motor brake ensures that the

tool stops quickly.

Changing the direction of rotation

♦ Change the direction of rotation by pushing the

rotation direction switch7 to the right or left.

Tips and tricks

Tip! How to do things correctly.

♦ Before operation, check whether the screw

or drill bit is correctly ﬁtted, i.e. centred in the

chuck.

♦ Screw bits are labelled according to their di-

mensions and their shape. If you are uncertain,

always check ﬁrst whether the bit ﬁts tightly in

the screw head without any play.

Torque

♦ Smaller screws/bits can be damaged if you

set too high a torque or too high a speed.

Hard screw joints (in metal)

♦ Particularly high torques occur, e.g. in metal

screw joints when using drive sockets. Select

a low rotational speed.

Soft screw joints (e.g. in soft wood)

♦ Here, too, use a low speed to avoid damaging

the wood surface when it comes into contact

with the metal screw head. Use a countersink.

Small screws can be screwed directly into soft

wood without predrilling.

When drilling in wood, metal and other

materials, observe the following:

♦ Use a high speed for drill bits with a small

diameter and a low speed for drill bits with

a large diameter.

♦ Select a low speed for hard materials and

a high speed for soft materials.

♦ Mark the spot where you want to drill using

a centre punch or nail. Select a low rotational

speed when starting.

♦ Pull the rotating drill bit from the hole repeatedly

to remove dust and chips and clear the hole.

Drilling in metal

♦ Use a metal drill (HSS). For optimum results,

you should cool the drill bit with oil.

Metal drill bits can also be used to drill into

plastics. Start with a 3 mm drill bit and then

increase the size until the desired hole diameter

is achieved.

Drilling in brick

♦ Use a carbide-tipped masonry drill (max.

recommended drill diameter 16 mm).

Drilling in wood

♦ Use a wood drill with a lathe centre; for deep

holes, use an auger bit; for large-diameter

holes, use a Forstner bit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PSBSAP 20-Li B3 - IAN 391011 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info