679615
10
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
11 GB/IE/CY
metals or metal objects left in wood. This can hap-
pen especially if the wood dust has paint particles
on it or is mixed with other chemical substances
and the sanded material is hot after extensive
working. You should therefore avoid overheating
of products being sanded as well as the appliance
and always empty the dust collection box
4
or
the dust bag of the vacuum cleaner before work
pauses.
Wear a dust mask!
Vacuuming dust with the dust
collection box
Attach the dust collection box:
j Push the dust collection box
4
on to the
device.
Remove the dust collection box:
j Press the release button(s)
3
and pull the dust
collection box
4
off the device.
NOTE: Always empty the dust collection box
4
in due time and shake any remaining dust out; this
will ensure optimal vacuum performance.
Dust extraction using an external
vacuum extraction device
Connecting:
j For vacuum dust removal using a vacuum
cleaner, push the suction hose of a vacuum
cleaner approved for use as a dust extraction
device (e.g. a workshop vacuum cleaner) into
the connection
5
see Fig. D.
NOTE: If it is necessary to use the reducer
piece
12
, push the reducer piece into the con-
nection
5
.
Removing:
j Pull the hose of the dust extraction device off
the connection
5
or off the reducer piece
12
,
if one is used.
Q
Instructions, tips and tricks
j Move the oscillating sander parallel, in flat
circles or alternating between lengthwise and
side-to-side motions.
j Do not press down with the oscillating sander.
The sanding pads become clogged, which
reduces the sanding performance.
j Clean the sanding pad
9
occasionally with
the vacuum cleaner.
j The removal performance and therefore the
result of your work are determined by the correct
selection of the speed and sanding pad
9
grit.
j Never sand different materials with the same
sanding pad
9
(e.g. wood then metal).
The following table offers some values, which are
for information only and may simplify the selection
of a sanding pad
9
.
Wood Sanding Pad / Grit
Sanding of wood 40 - 240
Pre-sanding, e.g.
of rough, unplaned
beams and boards
40, 60
Surface sanding 80, 100, 120
Fine sanding of hard
woods
180, 240
Paints / Lacquers Sanding Pad / Grit
Sanding of paint /
lacquer coats
or base coats
such as filler and
smoothing com-
pound
40 - 320
Sanding off paint 40, 60
Sanding off primer
coats
80, 100, 120
Final sanding of base
coats before painting
180, 240, 320
Operation
35324_ORBITAL SANDER_Content_LB6.indd 11 23.07.09 15:23
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PSS 250 - KH 3034 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Parkside PSS 250 - KH 3034

Parkside PSS 250 - KH 3034 Bedienungsanleitung - Deutsch, Holländisch, Französisch - 33 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info