786095
22
Zoom out
Zoom in
Vorherige Seite
1/124
Nächste Seite
22
GB IE
Initial start-up
Attaching sanding sheet
Clean the sanding plate before at-
taching a sanding sheet.
Remove the mains plug rst.
Use only appropriate sanding sheet
sizes. Sanding sheets that protrude
laterally beyond the sanding plate
can cause injuries and can cause
the sanding sheets to block or tear.
The sanding plate (7) is tted with Velcro for
rapid attachment of the sanding sheet (9).
Sanding sheet with Velcro:
1. Ensure that the sanding sheet (9) lies ush.
2. Press the sanding sheet (9) evenly onto
the sanding plate (7).
Ensure that the holes are placed direct-
ly above the extraction openings of the
sanding plate (7).
Sanding sheet without Velcro:
1. Release the two clamping levers (6).
2. Slide the sanding sheet under one of
the clamps (5).
3. Clamp the sanding sheet by locking the
clamping lever (6).
The sanding sheet must lie evenly and
tightly on the sanding plate (7).
4. Clamp the other end of the sanding
sheet in the same way.
Attaching /removing /
emptying dust collection
box
Attaching the dust collection box:
1. Before connecting, ensure that the dust
collection box (4) is rmly closed.
2. You must keep the dust collection box
(4) slightly slanted when pushing it
on. Slide the dust collection box (4) all
the way onto the connection for dust
extraction (12). The nose of the dust
collection box (4) must be inserted into
the groove (13) of the connector (12).
3. Then tighten the dust collection box (4)
clockwise to lock.
Removing the dust collectionbox:
4. Grasp the dust collection box (4) by
the black section.
Unlock the dust collection box (4) coun-
terclockwise and pull the dust collec-
tion box (4) off.
Emptying the dust collectionbox:
5. Open the dust collection box (4) by
slightly squeezing it on the transparent
part and pulling the two parts apart.
The dust box can be opened more ea-
sily by simultaneously pressing together
the black part of the dust collection
box from above and below.
Please note the arrows in Fig. for
the direction of pressure.
6. Remove the lter insert (11) and empty it.
7. Re-insert the lter insert (11) and close
the dust collection box (4).
Empty the dust collection box regu-
larly to ensure optimal suction.
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PSS 270 C3 IAN 360552 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info