Bedienungsanleitung Parkside PSTDA 18-Li A1 - IAN 102866 (Seite 11 von 89) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Finnisch)

576682

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

PSTDA 18-Li A1

Initial use

Fitting/changing the saw blade

Remove the battery before carrying out any

work on the power tool (e.g. maintenance, tool-

changing, etc.) as well as during carriage and

storage of the power tool.

Unintentional depressing of the On/Oﬀ button can

result in injury.

♦ Push the protective cover together at the two

outer holders and pull it oﬀ toward the front.

♦ Turn the quick-release chuck and hold it in

this position.

♦ Press the required saw blade into the quick-

release chuck as far as the limit stop.

♦ Release the quick-release chuck it must return to

its initial position. The saw blade is now locked.

Fitting the protective cover

Mount the protective cover before connecting

the machine to the dust extraction.

♦ Mount the protective cover onto the machine

in such a manner that the two outer holders

engage in the openings on the casing.

♦ Remove the protective cover for applications

without dust extraction as well as when perform-

ing mitre cuts. For this, push the protective cover

together at the two outer holders and pull it

oﬀ toward the front.

Fitting the guide fence

The guide fence can be ﬁ xed on the left- or

right-hand side of the appliance.

♦ Undo both the locking screws on the insertion

openings .

♦ Push the guide fence into the insertion

openings .

♦ Re-tighten the two locking screws.

Connecting the sawdust extraction

device

♦ Push the extraction nozzle into the vacuum

extraction duct until it is secured.

Optional depending on the diameter of the dust

and sawdust extractor.

♦ Attach an approved dust and sawdust extractor

to the extraction nozzle .

Supporting the extraction function:

♦ Slide the sawdust blower switch to the rear.

Sawdust blowing function

Switching the sawdust blowing function on:

♦ Press the sawdust blower switch forwards.

Fitting the splinter guard

The splinter guard can prevent fraying of the

surface while sawing wood. The splinter guard

can only be used for certain saw blade types,

without the sliding shoe and only for cutting

angles of 0°.

♦ Press the splinter guard from below into the

baseplate (notch facing upwards).

Fitting the sliding shoe

When working on sensitive surfaces, you can ﬁ t

the sliding shoe on the baseplate to avoid

scratching the surface.

♦ Mount the sliding shoe onto the baseplate

and press it up at the back until it clicks into

place on the baseplate .

♦ To remove the sliding shoe , unfasten it at

the rear of the baseplate and slide it oﬀ

forwards.

Operation

Setting the cutting angle

♦ Undo the locking screws with the supplied

Allen key and pull the baseplate to the rear.

♦ Adjust the cutting angle to 0°/15°/30°/45°

with the aid of the markings on the baseplate .

Push the baseplate to the front so that the lock-

ing pin engages in the toothing .

♦ Re-tighten the locking screws with the Allen

key.

IB_102866_PSTDA18-LiA1_LB3.indb 7 22.10.14 13:47

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PSTDA 18-Li A1 - IAN 102866 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info