Bedienungsanleitung Parkside PSZ 250 B2 - IAN 100684 (Seite 8 von 53) (Deutsch, Englisch, Holländisch, Polnisch)

595354

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

8 GB

Before beginning, verify the steel cable

wound around the drum

correctly and the

clearance between the turns is smaller than the

steel cable (Fig. B).

Before using

Mounting (see Fig. C)

Secure the cable hoist to a square pipe / boom

using the 2 mounting brackets

. The dimensi-

ons of the square pipe / boom must correspond

with the size of the mounting bracket

and

must be able to bear double the rated load.

Note: We recommend contact a qualiﬁed

technician for this purpose.

Screw the mounting brackets

to the cable

hoist (also see Fig. C).

Tighten all screws.

Note: A qualiﬁed technician should inspect

the anchor of the square tube / boom before

putting the device into service.

Note: The cable hoist motor

is equipped

with a thermostat switch. The motor

may

there-

fore stop whilst operating the cable hoist; it will

automatically restart once it has cooled down.

Setting up the pulley function

(see Fig. D–G)

The cable hoist is equipped with a pulley

and

an additional hook

. When used correctly, the

cable hoist can lift double the load.

Install the pulley

and additional hook

as shown in ﬁgures D–G.

Hook the ﬁxed hook

into the ﬁxing opening

(see Fig. G). The load will now be lifted with

two steel cables and the cable hoist can there-

fore lift double the load.

Operation

Putting the cable hoist

into service

The user must hoist the load from the ground at

the slowest possible speed. The cable must be

tightened when the load is being hoisted.

Secure the device with a 10 A fuse or a 10 A

earth leakage circuit breaker to protect the

electric circuit.

Before beginning, verify the steel cable

wound around the drum

correctly and the

clearance between the turns is smaller than the

steel cable (Fig. B).

Remove the adhesive tape from the cable drum

prior to ﬁrst use.

Ensure the load is properly secured to the hook

or, for pulley operation, the additional hook

, and always maintain a distance to the

load and the steel cable

Operating the cable hoist

Check if the emergency stop switch

pressed.

Turn the emergency stop switch

clockwise

to release.

Press the push button ▲

to hoist the load

(see Fig. H).

Press the push button ▼

to lower the load

(see Fig. H).

Auto-stop mechanism lever

When the maximum hoisting height has been

reached,

the shut-oﬀ weight

will push the lever

ward.

This engages a limit switch and the load can no

longer be hoisted.

Maximum cable length lever

When the load reaches the lowest possible position,

an end switch is activated, preventing the load from

being lowered further. This end switch also prevents

the cable hoist from being operated in the wrong

direction (hook moving opposite of the direction

indicated on the push button

Operation / Cleaning, maintenance and ordering spare parts / Disposal

Safety notices specific to the device / Before using / Operation

100684_par_Seilhebelzug_content_PL_SI_SK_NL.indd 8 02.07.14 12:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PSZ 250 B2 - IAN 100684 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info