Bedienungsanleitung Parkside PTK 2000 A1 - IAN 104416 (Seite 12 von 64) (Deutsch, Englisch, Holländisch, Französisch)

595333

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

7GB

• Table length extension

• Push stick

• Legs (4x)

• Cross struts (2x)

• Longitudinal struts (2x)

• Center struts, short (2x)

• Center struts, long (2x)

• Rubber feet (4x)

• Stability bar (2x)

• Table support, short (4x)

• Table support, long (2x)

Installation material

a) Washer (58x)

b) Nut (38x)

c) Hex screw (30x)

d) Phillips head screw (4x)

g) Retaining ring (58)

n) Round head screw M6x12 (24x)

m) Round head screw M6x16 (4x)

Tools

r) Open-ended wrench, size 22

s) Ring wrench, size 10/24

t) Open-ended wrench, size 8/10

4. Intended use

The bench-type circular saw is designed for the slitting

and cross-cutting of all types of timber, commensurate

with the machine’s size.

The machine is not to be used for cutting any type of

roundwood.

The machine is to be used only for its prescribed pur-

pose. Any use other than that mentioned is considered

to be a case of misuse. The user/operator and not the

manufacturer shall be liable for any damage or injury

resulting such cases of misuse.

The machine is to be operated only with suitable saw

blades. It is prohibited to use any type of cutting-off

wheel. To use the machine properly you must also

observe the safety regulations, the assembly instruc-

tions and the operating instructions to be found in this

manual. All persons who use and service the machine

have to be acquainted with this manual and must be

informed about its potential hazards. It is also imperative

to observe the accident prevention regulations in force

in your area. The same applies for the general rules of

occupational health and safety.

m Important!

When using the equipment, a few safety precautions

must be observed to avoid injuries and damage. Please

read the complete operating instructions and safety

regulations with due care. Keep this manual in a safe

place, so that the information is available at all times.

If you give the equipment to any other person, hand

over these operating instructions and safety regulations

as well. We cannot accept any liability for damage or

accidents which arise due to a failure to follow these

instructions and the safety instructions.

The manufacturer shall not be liable for any changes

made to the machine nor for any damage resulting from

such changes.

Even when the machine is used as prescribed it is still

impossible to eliminate certain residual risk factors.

The following hazards may arise in connection with the

machine’s construction and design:

• Contact with the saw blade in the uncovered saw

zone.

• Reaching into the running saw blade (cut injuries).

• Kick-back of workpieces and parts of workpieces

• Saw blade fracturing.

• Catapulting of faulty carbide tips from the saw blade.

• Damage to hearing if essential ear-muffs are not

worn.

• Harmful emissions of wood dust when the machine is

used in closed rooms.

m Please note that our equipment has not been de-

signed for use in commercial, trade or industrial appli-

cations. Our warranty will be voided if the machine is

used in commercial, trade or industrial businesses or

for equivalent purposes.

5. Safety information

m Attention! The following basic safety measures

must be observed when using electric tools for protec-

tion against electric shock, and the risk of injury and

re. Read all these notices before using the electric

tool and keep the safety instructions for later refer-

ence.

Safe work

1 Keep the work area orderly

– Disorder in the work area can lead to accidents.

2 Take environmental inuences into account

– Do not expose electric tools to rain.

– Do not use electric tools in a damp or wet envi-

ronment.

– Make sure that the work area is well-illuminated.

– Do not use electric tools where there is a risk of

re or explosion.

3 Protect yourself from electric shock

– Avoid physical contact with earthed parts (e.g.

pipes, radiators, electric ranges, cooling units).

4 Keep children away

– Do not allow other persons to touch the equipment

or cable, keep them away from your work area.

5 Securely store unused electric tools

– Unused electric tools should be stored in a dry,

elevated or closed location out of the reach of

children.

6 Do not overload your electric tool

– They work better and more safely in the specied

output range.

7 Use the correct electric tool

– Do not use low-output electric tools for heavy work.

– Do not use the electric tool for purposes for which

it is not intended. For example, do not use hand-

held circular saws for the cutting of branches or

logs.

– Do not use the electric tool to cut rewood.

8 Wear suitable clothing

– Do not wear wide clothing or jewellery, which can

become entangled in moving parts.

– When working outdoors, anti-slip footwear is

recommended.

– Tie long hair back in a hair net.

9 Use protective equipment

– Wear protective goggles.

– Wear a mask when carrying out dust-creating

work.

10 Connect the dust extraction device if you will

be processing wood, materials similar to wood,

or plastics.

– If connections for dust extraction and a collect-

ing device are present, make sure that they are

connected and used properly.

– When processing wood, materials similar to

wood, and plastics. operation in enclosed

spaces is only permitted with the use of a suit-

able extraction system.

Parkside PTK 2000 A1 - IAN 104416 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info