595341
13
Zoom out
Zoom in
Vorherige Seite
1/82
Nächste Seite
13 GB/IE
Safety notices specific to the device Safety notices specific to the device / Start-up
Wear a dust mask!
Not approved for wet-grinding!
Approved tool diameter
Safety notices for grinding tools
a) General
Grinding tools are susceptible to breakage. There-
fore utmost care needs to be taken when handling
grinding tools. Using damaged or wrongly inserted
or clamped in grinding tools is dangerous and can
lead to severe injuries.
b) Handling, transport and storage
Grinding tools have to be handled and transported
with care. Grinding tools have to be stored in such
a way that they are not exposed to mechanical dam-
age or damaging environmental influences.
Avoid the danger of death from electric
shock:
R
egularly check the condition of the device, m
ains
cable and the mains plug. Do not operate ap-
pliances with damaged parts of that description.
Never open the appliance. Damaged appliances
,
mains cables or plugs main danger to life du
e to
electric shock. Always have repairs or parts ex-
changes carried out at the service centre or by
an electrician.
D
o not operate the device whilst moist or in dam
p
environments.
When working outdoors, connect the device to
a earth leakage circuit breaker (ELCB) with a
max. tripping current of 30 mA. Only use exten-
sion leads approved for outdoor use.
Note: Always keep the mains cable away from
the sphere of the device and guide it to the back,
away from the device.
Start-up
Switching on and off
Switching on:
Pull the ON / OFF switch
6
towards the back
(see Fig. A).
Switching off:
Release the ON / OFF switch
6
.
Releasing the plunge blocker
Push the plunge blocker
1
towards the front
and keep it pressed.
Preselect cutting depth
Note: We recommend adjusting the cutting depth
at least 2 mm deeper than the thickness of the ma-
terial. This will result in a clean cut.
Release the quick release of the cutting depth
pre-selector
7
, adjust the desired cutting depth
at the scale
7 a
and refit the quick release.
Fitting the guide fence
Release the screw of the guide fence
11 a
at
the base plate
9
and insert the guide fence
11
into the guide fence fixture
10
. Retighten these
screws
11 a
.
Handling the plunge saw
1. Put the machine onto the material and switch it on
as described in the chapter “Switching on and off”.
2. If necessary adjust the machine to the guide
fence
11
or a drawn line.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

parkside-pts-500-a1---ian-103316

Suche zurücksetzen

  • pour un pignon d,entraînement pour parkside pts 500 a1 Eingereicht am 1-5-2020 16:32

    Antworten Frage melden
  • wie kann ich die Bedienungsanleitung von der Tauchsäge PTS 500 B2 herunterladen. Eingereicht am 21-4-2020 17:53

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PTS 500 A1 - IAN 103316 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info