Bedienungsanleitung Parkside PTS 500 C3 - IAN 286507 (Seite 28 von 132) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

706354

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Q Plunge saw warnings

Safety instructions for all saws –

Cutting procedures

DANGER! Keep hands away

from cutting area and the

blade. If both hands are holding the saw,

they cannot be cut by the blade.

2. Do not reach underneath the

workpiece. The guard cannot protect you

from the blade below the workpiece.

3. Adjust the cutting depth to the

thickness of the workpiece. Less than a

full tooth of the blade teeth should be visible

below the workpiece.

4. Never hold piece being cut in your

hands or across your leg. Secure the

workpiece to a stable platform. It is

important to support the work properly to

minimise body exposure, blade binding, or

loss of control.

5. Hold the power tool by insulated

gripping surfaces only, when

performing an operation where

the cutting tool may contact hidden

wiring or its own cord. Contact with

a “live” wire will also make exposed metal

parts of the power tool “live” and could give

the operator an electric shock.

6. When ripping, always use a rip fence

or straight edge guide. This improves

the accuracy of cut and reduces the chance

of blade binding.

7. Always use saw blades with correct

size and shape (diamond versus

round) of arbour holes. Blades that do

not match the mounting hardware of the saw

will run eccentrically, causing loss of control.

8. Never use damaged or incorrect

blade washers or bolts. The blade

washers and bolt were specially designed

for your saw, for optimum performance and

safety of operation.

Further safety instructions for all saws –

Kickback causes and related warnings

A kickback is a sudden reaction to a pinched,

bound or misaligned saw blade, causing

an uncontrolled saw to lift up and out of the

workpiece toward the operator;

¢ when the blade is pinched or bound tightly

by the kerf closing down, the blade stalls and

the motor reaction drives the unit rapidly back

toward the operator;

¢ if the blade becomes twisted or misaligned

in the cut, the teeth at the back edge of the

blade can dig into the top surface of the

wood causing the blade to climb out of the

kerf and jump back toward the operator.

Kickback is the result of saw misuse and / or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

1. Maintain a ﬁrm grip on the saw and

position your arms to resist kickback

forces. Position your body to either

side of the blade, but not in line with

the blade. Kickback could cause the saw

to jump backwards, but kickback forces

can be controlled by the operator, if proper

precautions are taken.

2. When blade is binding, or when

interrupting a cut for any reason,

release the trigger and hold the

saw motionless in the material

until the blade comes to a complete

stop. Never attempt to remove

the saw from the work or pull the

saw backwards while the blade is

in motion or kickback may occur.

Investigate and take corrective actions to

eliminate the cause of blade binding.

3. When restarting a saw in the

workpiece, centre the saw blade in

the kerf and check that saw teeth

are not engaged into the material.

If saw blade is binding, it may walk up or

kickback from the workpiece as the saw is

restarted.

4. Support large panels to minimise the

risk of blade pinching and kickback.

Large panels tend to sag under their own

weight. Supports must be placed under the

panel on both sides, near the line of cut and

near the edge of the panel.

5. Do not use dull or damaged blades.

Unsharpened or improperly set blades

produce narrow kerf causing excessive

friction, blade binding and kickback.

6. Blade depth and bevel adjusting

locking levers must be tight and

secure before making cut. If blade

adjustment shifts while cutting, it may cause

binding and kickback.

7. Use extra caution when sawing into

existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback.

30 GB / IE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PTS 500 C3 - IAN 286507 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info