Bedienungsanleitung Parkside PTS 500 C3 - IAN 286507 (Seite 31 von 132) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

706354

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into

the surface of the material causing the wheel to

climb out or kick out. The wheel may either jump

toward or away from the operator, depending on

direction of the wheel’s movement at the point of

pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse

and / or incorrect operating procedures or

conditions and can be avoided by taking proper

precautions as given below.

1. Maintain a ﬁrm grip on the power

tool and position your body and

arm to allow you to resist kickback

forces. Always use auxiliary handle,

if provided, for maximum control

over kickback or torque reaction

during start-up. The operator can control

torque reactions or kickback forces, if proper

precautions are taken.

2. Never place your hand near the

rotating accessory. Accessory may

kickback over your hand.

3. Do not position your body in line

with the rotating wheel. Kickback will

propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

4. Use special care when working

corners, sharp edges etc. Avoid

bouncing and snagging the

accessory. Corners, sharp edges or

bouncing have a tendency to snag the

rotating accessory and cause loss of control

or kickback.

5. Do not attach a saw chain,

woodcarving blade, segmented

diamond wheel with a peripheral

gap greater than 10 mm or toothed

saw blade. Such blades create frequent

kickback and loss of control.

6. Do not “jam” the wheel or apply

excessive pressure. Do not attempt

to make an excessive depth of cut.

Overstressing the wheel increases the loading

and susceptibility to twisting or binding of

the wheel in the cut and the possibility of

kickback or wheel breakage.

7. When wheel is binding or when

interrupting a cut for any reason,

switch oﬀ the power tool and hold

the power tool motionless until the

wheel comes to a complete stop.

Never attempt to remove the wheel

from the cut while the wheel is in

motion otherwise kickback may

occur. Investigate and take corrective action

to eliminate the cause of wheel binding.

8. Do not restart the cutting operation

in the workpiece. Let the wheel

reach full speed and carefully re-

enter the cut. The wheel may bind, walk

up or kickback if the power tool is restarted in

the workpiece.

9. Support panels or any oversized

workpiece to minimize the risk of

wheel pinching and kickback. Large

workpieces tend to sag under their own

weight. Supports must be placed under the

workpiece near the line of cut and near the

edge of the workpiece on both sides of the

wheel.

10. Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring

or objects that can cause kickback.

Safety warnings for diamond discs

1. Cutting-oﬀ tools are very fragile and likely to

break which is why great care must be taken

when handling the cutting-oﬀ tools. Using

damaged, incorrectly clamped or incorrectly

installed cutting-oﬀ tool is dangerous and may

cause serious injury.

2. Cutting-oﬀ tools are to be treated with care

and transported carefully. Cutting-oﬀ tools

should be stored in such a way that they

are not exposed to mechanical damage or

harmful environmental inﬂuences.

Laser safety warnings

WARNING! PRODUCT YOURSELF

FROM LASER RADIATION!

P max.: < 1 mW, λ: 650 nm

EN 60825-1:2014

This product contains a Class 2 laser.

33 GB / IE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PTS 500 C3 - IAN 286507 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info