Bedienungsanleitung Parkside PTS 500 C3 - IAN 286507 (Seite 34 von 132) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

706354

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

NOTE

u The power indicator

is lit when the

product is connected to the mains.

1. Press the spindle lock button

to lock the

spindle (see ﬁg. B).

2. Use the provided hex key

to loosen

clockwise and remove the blade bolt with

washer

and locking ﬂange

(see ﬁg.C). The blade bolt

uses a left-

hand thread.

3. Loosen the cutting depth selector with

indicator

4. Press the plunge lock button

forward and

swivel the base plate

up.

5. Remove the saw blade

. Do not remove

the backing ﬂange.

Follow the above procedure in reverse order

to attach blades. Pay attention to the correct

alignment of the locking ﬂange

Q Attaching / removing a dust

extraction device

WARNING!

u During operation ﬁne dust will be generated!

Some dusts are highly inﬂammable and

explosive! Always attach a dust extraction

device when using this product in order to

keep the working area clean! Wear a dust

mask when operating this product! Dust can

be harmful to health! Especially dust and

chips of wood that has been treated, e.g.

with wood preservative or a stain!

u Do not smoke during operation, keep heat

sources and open ﬂames out of the working

area!

This product features a designated dust extraction

outlet

to connect a vacuum cleaner reducing

generated dust during operation on the workpiece

and airborne.

1. Align the slots of the dust extraction hose

with the keys of the dust extraction outlet

slide it over and lock by turning clockwise.

Follow the above procedure in reverse order to

remove the dust extraction hose

after work.

Q Inserting / changing batteries

of the laser

This product features a laser to guide cuts, which

is powered independently from the product with

batteries.

1. Use a suitable crosshead screwdriver to

loosen and remove the screw from the battery

compartment cover

(see ﬁg. E).

2. Take oﬀ the battery compartment cover

and pull out exhausted batteries if present.

3. Insert new batteries by pushing them in

between the contacts, observing their correct

polarity as marked on the batteries and the

battery compartment.

4. Place the battery compartment cover

back

onto the battery compartment and secure it

with the screw.

Q Operation

CAUTION! RISK OF INJURY!

u Keep your hands away from the accessory

when the product is in operation.

Q Setting the cutting depth

NOTE

u Select a cutting depth of approx. 3 mm

more than the thickness of the material. This

ensures that you achieve a clean cut.

1. Loosen the cutting depth selector

, set the

desired cutting depth with its indicator on the

cutting depth scale

and retighten it at the

desired position.

Q Switching the laser on and oﬀ

Switching on:

1. Slide the on / oﬀ switch for the laser

the position “ON” to switch the laser on.

Switching oﬀ:

2. Slide the on / oﬀ switch for the laser

the position “OFF” to switch the laser oﬀ.

NOTE

u Always remember to switch oﬀ the laser after

work to avoid draining the batteries.

36 GB / IE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PTS 500 C3 - IAN 286507 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info