Bedienungsanleitung Parkside PUV 2000 B1 - IAN 354722 (Seite 10 von 98) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Polnisch)

764043

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

GB│IE │ 5 ■

PUV 2000 B1

Operation

Before Operation

Mount the device

NOTE

► Place the unit on a ﬂat surface. The cable

must be routed in the device as shown in

ﬁgure A (detailed view). Insert the cable with

a loop into the unit. It must not exceed the

housing of the appliance. The cover of the

housing must be easy to install. Make sure

that the cable is not pinched.

♦ Place the cover on the device and screw it with

the supplied mounting screws (see Fig. A).

Mount the stand 6

♦ Attach the stand 6 to the unit (see Fig. B).

Operation

♦ Push the loop of the extension cable into the

provided strain relief 2 in the handle 1 and

ﬁx it to the bar provided.

♦ Connect the appliance to a power socket

(230V alternating current) using an extension

cable.

♦ Switch the appliance on by pressing the ON/

OFF switch 4. The full operating temperature is

reached after approx. 1 minute (see Fig. C).

♦ To kill weeds, now place the cone nozzle 9

onto the plant to be treated for around

5–10seconds depending on the type of plant.

Keep at a distance of approximately 3 cm.

Guide the opening of the cone nozzle slowly

and parallel to the ground (see Fig. D, detailed

view).

♦ For taller plants, ﬁrst only heat the upper section

of the plant brieﬂy and then place the cone

nozzle 9 against the shrunken plant for

approx. 5–10seconds (see Fig. D).

NOTE

► Burning the plants oﬀ completely is not essen-

tial. During heating, the leaf cells dry out and

the weed will die (see Fig. F).

► To begin with, overgrown areas must be

treated several times at short intervals in

order to produce long-term success. After this,

treatment at longer intervals is suﬃcient. The

heat ﬂowing out of the nozzle penetrates far

into the root system and causes the cell ﬂuid

ofthe plant cells to coagulate. This expansion

causes the cell walls to burst.

► This appliance is particularly suitable for

removing weeds.

► Weedkilling is most eﬀective at an early

stage of vegetation growth.

► The most suitable time is during spring.

► The treatment is at its most intensive the

younger the plant is. However, the success

of the measure is not immediately visible.

The visible section of the plant can also be

burnt oﬀ with a longer exposure time/treat-

ment.

► Plants do not react immediately to the heat

radiation with the recommended treatment

time.

The following applies as a basic principle:

young, soft-leaved plants react most sensi-

tively to treatment. They are subsequently no

longer capable of survival.

► Older plants with hard leaves such as thistles

must be treated more frequently at an interval

of between 1 and 2weeks in order to make

them dry out.

Winter-green grasses are extremely robust

and require longer treatment.

► Repeated treatment of certain types of weed

may be necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PUV 2000 B1 - IAN 354722 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info