764038
28
Zoom out
Zoom in
Vorherige Seite
1/160
Nächste Seite
28
GB IE
the safety switch (10) are in the correct
position.
The device will not turn on if the
collection box and safety switch are
not in the correct position.
Switching on and off
Make sure that the mains voltage
matches the details on the type pla-
te.
1. Make a loop in the end of
the extension cable and
suspend this in the cable
strain relief (7) on the mains
cable (6).
2. Re-connect the extension cable.
3. Make sure that the hopper (3) is empty
before switching on.
4.
1
2
To start the device,
slide the rotary
switch (2) lock
(2a) in the direction
.
Turn the rotary switch to the right. The
device is now in continuous operation.
5. Fill the hopper with the material to be
shredded (3).
The material is drawn in and sh-
redded.
6. To turn off, turn the rotary switch (2) left
to the OFF position.
The device will continue to run after
switching off.
Changing the rotational
direction (reverse)
You can change the rotational direction of
the cutting roll (reverse) to remove jammed
material.
1.
1
2
Slide the rotary
switch ( 2) lock
(2a) in the direc-
tion of the power
cable.
2. Turn the rotary switch to the left. The
device is now in inching mode.
jammed shredded material is re-
leased.
3. Change the rotational direction again
to continue shredding (see section
“Operation/switching on and off”).
Emptying the
collection box
Empty the collection box regularly.
Be aware that the collection box lls
unevenly under the discharge chute!
1. Switch off the device and unplug the
mains plug from the socket.
2. Unlock the collection box (11) by mo-
ving the safety switch (10) to the “OFF”
position.
3. Remove the collection box from the
chassis (9) and empty it.
4. Make sure that the area around the sa-
fety switch is free of wood chips before
inserting the collection box again.
5. Put the collection box back in place
and move the safety switch up as far as
it will go.
Overload protection
If the motor is overused, e.g.if the cutting
roll is blocked due to branches that are too
thick, the device switches off automatically.
Restart lock
If the device automatically shuts down due
to overuse, it will not restart automatically.
28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PWH 2800 A1 - IAN 354711 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info