Bedienungsanleitung Parkside PWSA 18 A1 - IAN 104454 (Seite 63 von 78) (Französisch)

595313

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

such as described below.

a) Hold the electric tool very

rmly and bring your body and your

arm into a position in which you can

resist the kickback force. Always use

the supplemental handle if available to

give you the best control over kickback

force or reaction time during accel-

eration. The operator can master the

kickback and reaction force through

suitable precautions.

b) Never bring your hands near a

rotating attachment tool. The at-

tachment tool can run over your hand

in the kickback.

c) Keep your body away from the

area in which the electric tool

would move during a kickback.

The kickback drives the electric tool in

the counter-direction to the rotation of

the grinding disc at the blocked spot.

d) Work particularly cautiously in

corner areas or where there are

sharp corners etc. Prevent the at-

tachment tools from recoiling from the

workpiece and jamming. The rotating

attachment tool tends to jam when near

corners, sharp edges or when it recoils

from such. This causes a loss of control

or kickback.

e) Do not use chain or toothed

saw blades. Such attachment tools

frequently cause a kickback or loss of

control over the electric tool.

Special safety instructions for

grinding and cutting

a) Use only grinders which have

been approved for your electric

tool and the protective hood in-

tended for these grinders. Grind-

ers which are not intended for the elec-

tric tool may not be sufciently shielded

and are unsafe.

b) Depressed centre grinding

wheels must be pre-mounted in

such a way that their grinding

surface does not protrude over

the level of the edge of the pro-

tective cover. An incorrectly mounted

grinding wheel which protrudes beyond

the level of the edge of the protective

cover cannot be adequately shielded.

c) The protective hood must be

securely attached to the elec-

tric tool and adjusted so that

the greatest level of safety is

reached, i.e., the smallest possible

amount of the grinder is exposed to the

operator. The protective hood should

protect the operator from broken bits

and accidental contact with the grinder.

d) Grinders may only be used for

the recommended attachment

options. For example: Never grind

with the side surface of a cutting disc.

Cutting discs are for cutting material

using the edge of the disc. Pushing

sideways on these grinders can break

them.

e) Always use undamaged clamp-

ing anges of the correct size

and shape for the grinding disc

you selected. Suitable anges sup-

port the grinding disc and thus reduce

the danger of the grinding disc break-

ing. Flanges for cutting discs can be

distinguished from anges for other

grinding discs.

f) Do not use worn grinding discs

for larger electric tools. Grinding

discs for larger electric tools are not

set up for the higher rotation speeds of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PWSA 18 A1 - IAN 104454 Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PWSA 18 A1 - IAN 104454

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info