Bedienungsanleitung Parkside PWSAP 20-L i A1 - IAN 289752 (Seite 30 von 114) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

722852

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

1. Adjust the guard

such that any sparks or

detached parts cannot hit either the user or

any bystanders.

2. The guard

must also be positioned such

that the sparks cannot ignite combustible

parts, including those in the surroundings.

3. Turn the guard

to the required position so

the clamp should match the notches on the

guard

Q Attaching / removing the

accessory

WARNING!

u Always remove the battery pack from the

product before changing the accessory in

order to avoid switching it on accidentally.

u Always use the correct accessories according

to the intended use! Observe the technical

requirements of this product (see section

Technical data) when purchasing and using

accessories!

u Accessories can be sharp and become hot

during use! Handle them carefully! Wear

safety gloves when handling accessories in

order to avoid injuries like burns and cuts!

u Never press the spindle lock whilst the

spindle is rotating!

u The arrow on the accessory must correspond

to the arrow showing the direction of rotation

(running direction shown on the product).

u Ensure that the accessory is suitable for the

rotational speed of the product.

u Do not use any saw blades.

CAUTION! RISK OF INJURY!

u Only use accessory recommended by the

manufacturer. Using other attachment tools

and other accessories can represent a risk of

injury for you.

u Only use accessory, which bear information

about the manufacturer, type of binding,

dimension and permitted number of

revolutions.

u Only use grinding discs where the printed

rotational speed is at least as high as what

has been speciﬁed on the product marking.

u Do not use any broken, cracked, or otherwise

damaged accessories.

u Only use ﬂawless grinding discs (ringing

test: when you strike the disc with a plastic

hammer, it results in a clear sound).

u Ensure that the accessory dimensions match

those of the product.

u Never re-drill a locating hole which is too

small to make it larger.

u Never use separate bushings or adapters in

order to make discs with a hole that is too

large ﬁt the product.

u Never operate the product without protective

equipment.

u Support plates or workpieces to reduce the

risk of kickback from a jammed disc. Large

workpieces may bend under their own

weight. The workpiece must be supported on

both sides of the disc, near the disc as well

as at the edge.

u Always reassemble the product completely

after replacing accessories.

1. Press and hold the spindle lock button

2. Release the locking ﬂange

, with the chuck

key

3. Mount the desired accessory onto the

backing ﬂange

. Label should always face

the product.

4. Mount the locking ﬂange

on the spindle.

5. Press and hold the spindle lock button

and tighten the locking ﬂange

tight again

using the chuck key

32 GB / IE

289752_CB8_DE_EN_FR_NL_CS_ES_PT_170930.indb 32 9/30/17 8:11 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PWSAP 20-L i A1 - IAN 289752 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PWSAP 20-L i A1 - IAN 289752

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info