Bedienungsanleitung Parkside PZKS 2000 B2 - IAN 338493 (Seite 13 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

779323

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

8GB/IE/NI

• Try to keep emissions as low as possible, for example by

limiting your working time. In this regard, all the operational

cycle phases must be taken into consideration (such as the

times when the tool is switched oﬀ or running idle).

8. Before starting the equipment

• Open the packaging and remove the device carefully.

• Remove the packaging material as well as the packaging

and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for transport damage.

• If possible, store the packaging until the warranty period has

expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, ﬁlm and small parts! There is a risk of swal-

lowing and suﬀocation!

• The equipment must be set up where it can stand securely.

Secure the machine on a workbench, base frame or similar.

Insert 4 screws (not included in the scope of delivery) into

the holes on the ﬁxed saw table (15). Tighten up the screws.

• Loosen the tilt protection (36) pre-installed at the bottom of

the saw, completely pull it out and secure it with an Allen

key (D).

• Adjust the adjusting screw (38) to the level of the tabletop to

avoid wobbling of the machine.

• All covers and safety devices have to be properly ﬁtted be-

fore the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed before,

watch out for foreign bodies such as nails or screws, etc.

• Before you press the ON/OFF switch check that the saw

blade is ﬁtted correctly. Moving parts must run smoothly.

• Before you connect the equipment to the power supply make

sure the data on the rating plate are identical to the mains

data.

8.1 Checking the moving saw blade guard safety

device (5)

The saw blade guard protects against accidental contact with

the saw blade and from chips ﬂying around.

Check function

To do so, fold the saw downwards:

• The saw blade guard must provide free access to the saw

blade without touching other parts.

• When folding the saw upwards into the starting position, the

saw blade guard must cover the saw blade automatically.

9. Attachment

9.1 Attaching the crosscut, drag and mitre saw

(ﬁg. 1/2/4)

• In order to adjust the rotary table (14), loosen the handle

(11) approximately 2 turns and pull up the latched position

lever (35) with your index ﬁnger.

• Turn the rotary table (14) and pointer (12) to the desired

angle measurement on the scale (13) and use the handle

(11) to secure it.

• Press the machine head (4) down lightly. The saw is un-

locked from the lower position by at the same time, pulling

out and turning the locking pin (23) from the engine mount.

• Turn the locking bolt (23) 90 degrees to secure it in the un-

locked position.

• Swing the machine head (4) up.

• It is possible to secure the clamping devices (7) to the left or

right on the ﬁxed saw table (15). Insert the clamping devices

(7) in the holes on the rear side of the stop rail (16) and se-

cure it with the star grip screws (7a). For 0°- 45° mitre cuts,

the clamping device (7) must only be mounted on the right

side (see ﬁg. 11-12).

• It is possible to tilt the machine head (4) a max. 45° to the

left by loosening the set screw (22).

• Workpiece supports (8) must always be secured and used

during work. Set the desired table size by loosening the set

screw (9). Then tighten the set screw (9) again.

9.2 Sawdust bag (ﬁg. 1/22)

The saw is equipped with a debris bag (17) for sawdust and

chips.

Squeeze the wings of the metal ring on the dust bag (17) to-

gether and slide it over the discharge port near the engine.

The debris bag (17) can be emptied by means of a zipper at

the bottom.

9.2.1 Connection to an external dust extractor

• Connect the vacuum hose with the dust extraction spout.

• The industrial vacuum cleaner must be suitable for the mate-

rial being worked.

• When vacuuming dust that is especially detrimental to health

or carcinogenic, use a special vacuum cleaner.

9.3 Precision adjustment of the stop for crosscut

90° (ﬁg. 1/2/5/6)

Tools required:

-Allen key 6 mm

-Open-ended spanner SW13 (not included in the scope of

delivery)

• No stop angle included.

• Lower the machine head (4) and secure it using the locking

bolt (23).

• Loosen the set screw (22).

• Position the angle stop (A) between the saw blade (6) and

the rotary table (14).

• Loosen the lock nut (26a).

• Adjust the adjusting screw (26) until the angle between the

saw blade (6) and rotary table (14) is 90°.

• Tighten the lock nut (26a) again.

• Subsequently check the position of the angle indicator. If

necessary loosen the pointer (19) using a Phillips screwdriv-

er, set to position 0° on the angle scale (18) and re-tighten

the retaining screw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PZKS 2000 B2 - IAN 338493 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info