Bedienungsanleitung Partner P340S (Seite 12 von 282) (Deutsch, Englisch, Dänisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

518739

Zoom out

Zoom in

Vorherige Seite

1/282

Nächste Seite

-- 11 --

MAINTENANCE INSTRUCTIONS

All chain saw service, other than items listed

here in your user manual maintenance

instructions, should be performed by a

professional.

A good preventive maintenance program of

regular inspection and care will increase life

and improve performance of your chain saw.

This maintenance checklist is a guide for

such a program.

Cleaning, adjustment, and parts replacement

may be required, under certain conditions, at

more frequent intervals than those indicated.

1. Remove knob (A) holding air filter cover in

place, remove the top cover (B) by

loosening the cover retaining screws.

Cover will lift off. (Fig.15A)

2. Lift the air filter (C) out of air-box (D)

(Fig.15B).

3. Clean air filter. Wash filter in clean, warm,

soapy water. Rinse in clear, cool water. Air

dry completely.

NOTE: It is advisable to have a supply of

spare filters.

4. Install air filter. Install engine / air filter

cover. Make sure latche (E) latch (F) and

cover fit properly. Tighten the cover

retaining knob securely. (Fig.15C &

Fig.15D)

1. Remove the fuel tank cap.

2. Bend a piece of soft wire to from a hook at

the end.

3. Reach into fuel tank opening and hook fuel

line. Carefully pull the fuel line toward the

opening until you can reach it with your

fingers.

NOTE: Do not pull hose completely out of

tank.

4. Lift filter (A) out of tank (Fig.16).

5. Pull filter off with a twisting motion. Discard

filter.

6. Install new filter. Insert end of filter into

tank opening. Make sure filter sits in

bottom corner of tank. Use a long

screwdriver to aid in filter placement if

necessary.

7. Fill tank with fresh fuel / oil mixture. See

Section FUEL AND LUBRICATION.

Install fuel cap.

1. Remove the 2 bolts (A) and pull muffler

out. (Fig. 17A).

2. Remove the 2 screws that holds the cover

(C). (Fig.17B)

3. Discard the used spark arrester screen (D)

andreplace it with a new one.

4. Reasemble the muffler components and

install the muffler to the cylinder. Tighten

securely.

WARNING: Never perform mainten-

ance when the engine is hot, to avoid any

chance of burning hands or fingers.

NOTE: A clogged spark arrester screen will

dramatically reduce engine performance.

WARNING: Never operate your saw

without a fuel filter. The fuel filter should be

replaced after each 20 hours of use. Drain

fuel tank completely before changing filter.

CAUTION: Never operate saw

without the air filter. Dust and dirt will be

drawn into engine and damage it. Keep the

air filter clean!

PREVENTIVE MAINTENANCE

AIR FILTER

TO CLEAN AIR FILTER:

Fig. 15A

Fig. 15B

Fig. 15C

Fig. 15D

FUEL FILTER

Fig. 16

SPARK ARRESTER SCREEN

HOURS OF

EACH

MAINTENANCE

CHECKLIST

USE

OPERATION

ITEM ACTION

Screws/Nuts/Bolts Inspect/Tighten

Air Filter Clean or Replace

Fuel Filter/Oil Filter Replace

Spark Plug Clean/Adjust/Replace

Spark Arrester Screen Inspect

Fuel Hoses Inspect

10 20

Replace as Required

Chain brake Inspect

components

Replace as Required

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Partner P340S Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info