Bedienungsanleitung Partner P4-20XT (Seite 9 von 15) (Deutsch, Englisch, Französisch, Spanisch)

518735

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

STARTING A COLD ENGINE (or a

warm engine after running out of

fuel)

NOTE

:In thefollowing steps,when thecho-

ke/fast idle lever is pulled out to the full ex-

tent, the correct throttle setting for starting is

set automatically.

ON/STOP SWITCH

STOP

(SIDE VIEW)

1. Move ON/STOP switch to the ON posi-

tion.

2. Slowly press primer bulb 6 times.

3. Pull out choke/fast idle to the full extent

(to the FULL CHOKE position).

4. Pull the starter rope sharply 5 times with

your right hand. Then, proceed to the

next step.

NOTE: If the engine sounds as if it is trying

to start before the 5th pull, stop pulling and

immediately proceed to the next step.

5. Push the choke/fast idle lever in to the

HALF CHOKE position.

OFF HALF

CHOKE/FAST IDLE LEVER

Choke/

fast idle lever

(SIDE VIEW)

FULL

6. Pull the starter rope sharply with your

right hand until the engine starts.

7. Allow the engine to run for approximately

30 seconds. Then, squeeze and release

throttle triggerto allow engine to returnto

idle speed.

STARTING A WARM ENGINE

1. Move ON/STOP switch to the ON posi-

tion.

2. Slowly press the primer bulb 6 times.

3. Pull the choke/fast idle lever out to the

HALF CHOKE position.

4. Pull the starter rope sharply with your

right hand until the engine starts.

5. Squeeze and release throttle trigger to

allow engine to return to idle speed.

DIFFICULT STARTING (or starting a

flooded engine)

The engine may be flooded with too much

fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess

fuel by pushing the choke/fast idle lever in

completely (to the OFF CHOKE position)

and then following the warm engine starting

procedure listed above. Ensure the ON/

STOP switch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly

the unit is flooded. If engine fails to start, re-

fer to the TROUBLESHOOTING TABLE.

CHAIN BRAKE

WARNING: If the brake band is worn

too thin it may break when the chain brake is

triggered. With a broken brake band, the chain

brake will not stop the chain. The chain brake

should be replaced by an authorized service

dealer if any part is worn to less than 0,02″ (0,5

mm) thick. Repairs on a chain brake should be

made by an authorized service dealer . Take

your unit to the place of purchase if purchased

from a servicing dealer , or to the nearest autho-

rized master service dealer .

S This saw is equipped with a chain brake.

The brake is designed to stop the chain if

kickback occurs.

S The inertia activated chain brake is acti-

vated if the front hand guard is pushed for-

ward, either manually or by centrifugal

force.

S If the brake is already activated, it is disen-

gaged by pulling thefront handgu ard back

toward the front handle as far as possible.

S When cutting with the saw,the chain brake

must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION:

The chain brake must be

checked several times daily. The engine

must berunningwhenperforming this proce-

dure. This is the only instance when the saw

should be placed on the ground with the en-

gine running.

Place the saw on firm ground. Grip the rear

handlewithyour righthand andthe fronthan-

dle with your left hand. Apply full throttle by

fully de pressing the throttle trigger. Activate

the chain brake by turning your left wrist

against the hand guard without releasing

your grip around the front handle. The chain

should stop immediately.

Inertia activating function control

WARNING:Whenperforming thefol-

lowing procedure, the enginemust beturned

off.

Grip the rear handle with your right hand and

the front handle with your left hand. Hold the

chain saw approximately 14” (35 cm) above

a stump or other wooden surface. Release

your grip on the front handle and use the

weight of the saw to let the top of the guide

bar fall forward and contact the stump.

When the tip of the bar hits the stump, the

brake should activate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Partner P4-20XT Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info