Bedienungsanleitung Peavy CS 4000 (Seite 8 von 56) (Englisch)

564335

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

000/

080

Power Amplifiers

Congratulations on your purchase of a Peavey CS Series power amplifier! Designed for years of reliable operation, CS Series

amplifiers offer the sonic superiority and unsurpassed reliability for which Peavey is famous in a rugged, compact unit.

Advanced technologies and extensive protection circuitry allow operation with greater efficiency, even under difficult loads

and power conditions. The DDT

™

(Distortion Detection Technique) circuit ensures trouble-free operation into loads as low

as 2 ohms (4 ohms for model CS

080 HZ), protects speakers and ensures, protects drivers and ensures sonic integrity even

in extreme overload conditions. Peavey’s high-efficiency design uses tunnel-cooled heat sinks and dual-speed DC fans for

consistent lower overall operating temperature, resulting in longer output transistor life.

Peavey CS Series amplifiers are simple to operate and housed in ultra-strong steel chassis, but improper use can be

dangerous. Some CS Series amplifiers are very high powered and can put out high voltages and sizable currents at frequencies

up to 30 kHz. Always use safe operating techniques with these amplifiers.

FOR YOUR SAFETY, READ THE IMPORTANT PRECAUTIONS SECTION, AS WELL AS INPUT, OUTPUT AND POWER

CONNECTION SECTIONS.

Unpacking

Upon

unpacking, inspect the amplifier. If you find any damage, notify your supplier immediately. Only the consignee

(the supplier from whom you purchased the amplifier) may institute a claim with the carrier for damage incurred

during shipping. Be sure to save the carton and all packing materials. Should you ever need to ship the unit back to

Peavey or one of its offices, service centers or the supplier, use only the original factory packing. If the shipping carton

is unavailable, contact Peavey to obtain a replacement.

Mounting

CS Series amplifiers will mount in standard 19" racks. Rear mounting ears are also provided for additional support,

which is recommended in non-permanent installations like mobile or touring sound systems. Because of the cables

and connectors on the rear panel, a right angle or offset screwdriver or hex key will make it easier to fasten the rear

mounting ears to the rails.

Cooling Requirements

CS Series amplifiers use a forced-air cooling system to maintain a low, consistent operating temperature. Air is

drawn into the amplifier by fans on the back panel and courses through the cooling fins of the tunnel-configured

channel heat sinks, then exhausts through the front panel grilles. If either heat sink gets too hot, a sensing circuit will

disconnect the load for that particular channel. It is important to have an air inlet at the back of the amplifier to allow

cooling air to enter. If the amp is rack mounted, do not use doors or covers on the back of the rack, as the intake air

must flow without resistance. Make sure that there is one (1) standard rack space opening for every three mounted

power amplifiers.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Peavy CS 4000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info