Bedienungsanleitung Peavy MuseBox (Seite 36 von 52) (Englisch)

564345

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

If you have a MIDI keyboard attached, you can send a MIDI program change message and

MuseBox will load the corresponding presets in that particular TAG. If you change to a different

TAG, then your program changes will select presets within that new TAG.

You can easily create a custom named TAG before your gig using the Graphical User Interface and

then TAG the presets of interest to reside in that TAG. If you don't have the GUI handy, you can

simply save the presets into the USER TAG and select them there.

If you want to move back and forth through the preset list, you can connect a 1/4" stereo to dual-

mono breakout cable to the footswitch jack and connect TWO footswitches to the rear panel. One

switch will allow you to increment through the list (increasing the preset number with each push of

the switch) and the other switch will allow you to decrement through the list (decreasing the preset

number with each push of the switch).

In either case, each time you press the footswitch, the next (or previous) preset will load

immediately. This function is ideal for guitarists who might want to move through different guitar

effects during a set without having to take their hands off their guitar to change patches.

Editing Virtual Instruments or Effects

The virtual instruments and effects in MuseBox are intended to be edited from their Graphical User

Interfaces which you can see when you connect an LCD monitor to your MuseBox, or when you use

the MuseBox Remote software with your Mac or PC through a network.

However, you can edit some of the key parameters on a plugin from the front panel by pressing

the EDIT button. The EDIT mode lets you adjust up to eight pre-dened editable parameters per

virtual instrument or effect.

To edit a virtual instrument or effect, rst you need to select the channel you want to edit. You do

this by simply pressing the SNTH1, SNTH2, AUD1, or AUD2 channel from the front panel.

In the case of MusePlayer, the default sound generating plugin in MuseBox, the parameters you can

adjust are:

1. Amplitude Envelope Attack 5. Master Filter Cutoff Frequency

2. Amplitude Envelope Decay 6. Master Filter Resonance

3. Amplitude Envelope Sustain 7. Filter Cutoff

4. Amplitude Envelope Release 8. Filter Q

For ReValver

™

, the default amp modeling plugin in MuseBox, the parameters you can adjust are:

1. PreAmp 1 Gain 5. Reverb Mix

2. Bass EQ 6. Presence

3. Mid EQ 7. Master Output

4. Treble EQ 8. PreAmp 2 Gain

MIDI Learn and Editable Paramaters

MuseBox supports "MIDI Learn" which allows you to assign various MIDI-controllable paramaters to

various MIDI continuous controllers. This feature requires you to use the Graphical User Interface,

and as such it is not covered in this quickstart guide, so please consult the website for more

information. However, it is important to realize the rst eight parameters that are assigned using

the MIDI Learn function show up as the rst eight parameters in when the EDIT button is lit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Peavy MuseBox Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Peavy MuseBox

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info