Bedienungsanleitung Peavy PV 900 (Seite 11 von 40) (Englisch)

564337

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

when relatively short 1/4" cable patches are made to this input from various outputs on this amplifier,

or from other equipment that shares the same rack with this amplifier. The quasi-balanced circuitry is

“automatic” and virtually “invisible” in normal usage. This feature can be defeated with a jumper on the

barrier strip from the “-” input terminal of that channel to the ground terminal.

(15) LOW CUT SWITCH

This switch is used to activate the LOW CUT filter for the corresponding channel. It is again a push-

push type switch, requiring a small “tool” to activate. The IN position routes the input signals through

the 40 Hz LOW CUT filter, while the OUT position bypasses the filter. This filter will cut extremely low

frequencies, protecting speakers from the possibility of over-excursion. The filter low-frequency rolloff

is 12 dB per octave. The LOW CUT filter for each channel will function independently of the crossover

function to be discussed next.

(16) CROSSOVER SWITCH (150 Hz XOVER)

This switch is used to activate the 150 Hz crossover for the corresponding channel. It is also a push-

push type switch and requires a small “tool” to activate. The PV

offers two 150 Hz crossovers. These

are specially designed features that enhance the response of most loudspeakers in a typical bi-amped

application. Rather than just having a flat output curve, these crossovers use special filters to tailor the

response and provide a flat acoustical output. This type of crossover “sounds” more natural than

conventional “state-variable” type crossovers.

With the switch IN, the input signals are routed through the crossover, and the low frequencies are

automatically sent to the corresponding channel. At the same time, the high frequencies are sent

to the HIGH OUT (18) jack and must then be patched to INPUT of the other channel of this amplifier

or to another amplifier input to complete the bi-amped system. Additionally, the low frequencies are

sent to the THRU/LOW OUT (17) jack, and can be patched to other amplifier inputs to permit even

larger systems. With the switch OUT the crossover is defeated, and the input signal is routed directly

to the respective power amp channel. The crossover frequency is fixed at 150 Hz and cannot be

changed. The crossover configuration is a 4-pole Linkwitz-Riley approximation.

(17) THRU/LOW OUT JACKS

As per previous crossover discussion, this 1/4" jack supplies low-frequency out signals from the

activated crossover for patching to additional power amplifier inputs, providing added flexibility in

larger bi-amped systems. When the crossover function is not activated, this jack converts to a THRU

function, where the output of the electronically balanced input circuitry is supplied to this jack. The

THRU function provides the means to patch a full range input signal to the other input of this

amplifier (parallel mode), or to other amp inputs in the same rack. This function allows one balanced

mixer feed to be connected to the amp via the desired balanced input connector (XLR, 1/4", Barrier),

and then further distributed locally. Regardless of the crossover switch position, this 1/4" jack provides

an unbalanced (tip/sleeve) output to be patched with single conductor shielded cables.

(18) HIGH OUT JACKS

Again, as per previous crossover discussion, this 1/4" jack supplies high frequency out signals from

the activated crossover for patching to this amplifier and/or additional power amplifier inputs. Unlike

the low-frequency crossover output, that is automatically routed to the associated channel, the high-

frequency output signal must be patched to some suitable input in order to complete the bi-

amped system. This 1/4" jack also provides an unbalanced (tip/sleeve) output to be patched with

single-conductor shielded cables.

INDUSTRIAL AND COMMERCIAL INSTALLATIONS

For commercial and other installations where sustained high-power operation is required, the

amplifiers should be mounted in a standard 19" rack. It is not necessary to leave a rack space

between each amplifier in the stack since each fan pulls air in from the rear and exhausts the hot air

out the front. However, an adequate cool air supply must be provided for the amplifier when rack

mounted. The internal fan must have a source of air that is not preheated by other equipment. The

amplifier will start up in low speed fan operation and will normally stay at low speed unless sustained

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Peavy PV 900 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info