Bedienungsanleitung Pelgrim PWD110 (Seite 43 von 48) (Englisch)

557054

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

406066

Problem/error Cause What to do ...?

The dryer does

not work.

• No voltage in the power outlet. • Check if the power cord plug is

correctly inserted into the power

outlet.

• Check the fuse.

There is voltage

in the outlet, but

the drum does

not spin and the

dryer does not

work.

• Program was not started

in accordance with the

instructions.

• The door is not properly

closed.

• Condensate tank is full.

• Delayed start function has

been selected.

• Reread the instructions for use again.

• Push the door towards the appliance.

• Empty the condensate tank (see

section Cleaning and Maintenance).

• Wait until the time indicated on the

display elapses.

Laundry is not

dried, or drying

temperature is

longer than 4h.

• Filters are not clean. The room

is not sufficiently ventilated.

• Inappropriate temperature in

the room.

• Laundry was not sufficiently

wrung or spun.

• Amount of laundry dried in

the appliance is too large or

insufficient.

• Clean the filters.

• Check whether water condenser is

cleaned.

• Install the dryer in an appropriate

room (see section Installation ...).

• Check if the temperature in the room

where the dryer is installed is too

high (over 25°C) or too low (below

5°C).

• Laundry inserted into the dryer was

not sufficiently wrung or spun, or an

inappropriate drying program was

selected.

• Use an appropriate program or use

the timed program. Increase the

final level of dryness for the selected

program (intensive drying function).

Poor

condensation

• Inadequate location of the

dryer.

• Check whether the ambient

temperature of the room is not too

high.

• Check whether the condenser is clean.

Unevenly dried

laundry.

• The amount of laundry dried at

a time is too large.

• Drying the pieces of different

thicknesses.

• Drying the different types of

laundry.

• Make sure the laundry is sorted by

type and size of items given the

selected program (see section Drying

– Preparing the Laundry and the

Program Table).

Error in the drum

lighting.

• There is no lighting when the

dryer door is opened.

• Disconnect the dryer from the power

mains and call an authorized service

unit.

On display: F3 • Full condensate tank.

• If the condensate tank is

empty, there is a pump failure.

• Empty the condensate tank (see

section Cleaning and Maintenance).

• Disconnect the appliance and call the

nearest service unit.

On display:F4 • Clogged filters.

• If the filters are clean, there

may be a compressor failure.

• Clean the filters.

• Disconnect the appliance and call the

nearest service unit.

On display:"LO" • Steam generator tank is empty • Add distilled water.

Write down the failure/error code: F0, F1, or F2, disconnect the appliance and call the

nearest authorized service (call center).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pelgrim PWD110 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pelgrim PWD110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info