Bedienungsanleitung PENTAGRAM P 6121-L2 (Seite 18 von 20) (Englisch)

523580

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

horNET P6121-L2 / P6122-09 / P6123-09

Troubleshooting

This chapter provides solutions to problems that may occur during the installation and

operation of the Wireless Cardbus/PCI/USB Adapter. Read the descriptions below to solve

your problems.

1. The Wireless Cardbus/PCI/USB Adapter does not work properly.

• Reinsert the Wireless Cardbus/PCI/USB Adapter into your PC’s PCI slot/Cardbus

slot/USB slot.

• Right click on My Computer and select Properties. Select the device manager and

click on the Network Adapter. You will find the Adapter if it is installed successfully.

If you see the yellow exclamation mark, the resources are conflicting. You will see

the status of the Adapter. If there is a yellow question mark, please check the

following:

• Make sure that your PC has a free IRQ (Interrupt ReQuest, a hardware interrupt on

a PC.)

• Make sure that you have inserted the right adapter and installed the proper driver. If

the Adapter does not function after attempting the above steps, remove the adapter

and do the following:

• Uninstall the driver software from your PC.

• Restart your PC and repeat the hardware and software installation as specified in

this User Guide.

2. I cannot communicate with the other computers linked via Ethernet in the

Infrastructure configuration.

• Make sure that the PC to which the Adapter is associated is powered on.

• Make sure that your Adapter is configured on the same channel and with the same

security options as with the other computers in the Infrastructure configuration.

3. What should I do when the computer with the Adapter installed is unable to

connect to the wireless network and/or the Internet?

• Check that the LED indicators for the broadband modem are indicating normal

activity. If not, there may be a problem with the broadband connection.

• Check that the LED indicators on the wireless router are functioning properly. If not,

check that the AC power and Ethernet cables are firmly connected.

• Check that the IP address, subnet mask, gateway, and DNS settings are correctly

entered for the network.

• In Infrastructure mode, make sure the same Service Set Identifier (SSID) is

specified on the settings for the wireless clients and access points.

• In Ad-Hoc mode, both wireless clients will need to have the same SSID. Please note

that it might be necessary to set up one client to establish a BSS (Basic Service Set)

and wait briefly before setting up other clients. This prevents several clients from

trying to establish a BSS at the same time, which can result in multiple singular

BSSs being established, rather than a single BSS with multiple clients associated to

it.

• Check that the Network Connection for the wireless client is configured properly.

• If Security is enabled, make sure that the correct encryption keys are entered on

both the Adapter and the access point.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

PENTAGRAM P 6121-L2 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info