Bedienungsanleitung Pentax AF360FGZ (Seite 30 von 33) (Englisch)

16505

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

Before taking the picture, firing a modeling flash helps

you to see how shadows are cast on the subject.

■ Procedure

Slide the setting switch down [yellow dot].

Check that the flash is ready, then press the

MODELING button. The flash will fire

continuously for one second.

After firing the modeling flash, slide the setting

switch up [white dot].

• To prevent the flash tube from overheating or

deteriorating, do not fire the modeling flash

more than 10 consecutive times. After the

tenth time, let the flash unit rest for at least 10

minutes.

• When used with *ist, the flash pop-up button

on the camera can also be used for modeling

flash.

• When used with the MZ-S, the illumination

button on the camera can also be use for

modeling flash. (Please refer to the camera’s

operating manual)

AF360FGZ feature a built-in red spotbeam projector

to assist the autofocus system in dim light and low-

contrast conditions. When using the flash with

autofocus camera in dark conditions, the spotbeam

will be projected automatically depending on the

ambient lighting conditions. With the sync mode

switch set to [S.B.], the AF360FGZ can be used

exclusively as a focusing aid in dim light.

1. Set the main switch to the [ON] position.

2. Set the sync mode switch to the [SB] position.

3. Set the camera to the autofocus mode.

4. Press the shutter release button halfway down.

The AF spotbeam will automatically be projected

lights up indicating that you are ready to shoot.

• The AF spotbeam does not work in bright light

conditions.

• If the In-focus indication does not light up in

several seconds, it means that the subject is

hard to autofocus. In this case, use the manual

focus mode to focus on the subject.

• To change the composition, raise your finger

off the shutter release button and press it

halfway down again to recompose the picture.

• When using the AF360FGZ's built-in AF

spotbeam, the AF spotbeam built into the

camera will not operate.

• The AF spotbeam on the flash unit works

accurately only when mounted onto the

camera's hot shoe. The AF spotbeam does not

operate accurately when the bounce flash is

used.

• The flash does not fire when using the

AF360FGZ spotbeam exclusively as a focusing

aid.

• The AF spotbeam does not work with SF 7

camera, refer to page 27.

AF SPOTBEAM

MODELING FLASH/TEST FLASH

SLOW-SPEED-SYNC FLASH

Using the AF360FGZ Spotbeam Exclusively as a

Focusing Aid

When using a normal flash to photograph a subject

in a night or evening setting, the background will

appear very dark because a normal flash light

cannot sufficiently light it. However, it is possible to

balance both subject and background by using the

flash to properly expose the foreground subject and

a slow shutter speed to expose the low light

background.

• When used with the *ist or MZ-S, modeling

flash is also possible with wireless (Refer to

page 37). (Refer to the camera operating

manual for the camera settings).

■ Test flash

Check that the flash is ready, then press the TEST

button. The test flash can be operated.

PENTAX AF360 FGZ/1 BODY 4/15/03 11:26 AM Page 54

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pentax AF360FGZ Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pentax AF360FGZ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info