Bedienungsanleitung Perel AC06 (Seite 4 von 22) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

622120

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

AC06

V. 03 – 22/02/2016 4 ©Velleman nv

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

 Protect this device from shocks and abuse. Avoid brute force when operating the device.

 Protect the device against extreme heat, dust and moisture.

 Familiarise yourself with the functions of the device before actually using it.

 All modifications of the device are forbidden for safety reasons.

 Only use the device for its intended purpose. Using the device in an unauthorised way will void the

warranty.

4. Features

 overload protection (for charger)

 integrated ampere meter

 for various motor cars, vans and light trucks

 included accessories:

o charging cable (1.5 m + 1.5 m)

o two clamps

o 2 replaceable spare fuses

5. Overview

Refer to the illustrations on page 2 of this manual.

red LED

green LED

yellow LED

fuse (20 A)

6. Preparation

Always check the condition of the cables and clamps before using the

battery charger. Do not use when damage is noticed!

 Disconnect the battery from the vehicle before charging. To do this, first remove the negative pole

connection, and then proceed with the positive pole connection.

 When applicable (non-sealed battery), check the level of the battery acid. When necessary, add

distilled water.

 Clean the poles with a steel brush or sandpaper.

 Make sure the battery charger is not connected to the mains.

 Connect the positive clamp of the battery charger (red) with the positive pole (+) of the battery.

Make sure the clamp is secured tight.

 Connect the negative clamp of the battery charger (black) with the negative pole (-) of the battery.

Make sure the clamp is secured tight.

7. Operation

 The status of the charging process is indicated by 3 LEDs on the front of the unit. Refer to the

illustration on page 2 of this manual.

 When the battery charger is correctly connected to the battery, the red LED [A] lights up.

Otherwise, check the polarity of the connections and the fuse [D].

 When the battery has filler caps, unscrew them before charging.

 To start charging the battery, connect the battery charger to the mains. Make sure the correct mains

voltage is supplied (see technical specifications below).

 The red LED [A] will remain on during the entire charging procedure.

 The yellow LED [B] indicates that the battery charger is connected to the mains and the charging

procedure is ongoing.

 If the yellow LED [B] does not light up, check the condition of the mains socket and the mains.

 When the yellow LED [B] turns off during charging, the circuit was interrupted by the internal

transformer overload protection system. Disconnect the charger from the mains and allow it to cool

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Perel AC06 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Perel AC06

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info