Bedienungsanleitung Perel CCTVSET10 (Seite 5 von 152) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

493720

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

CCTVSET10

26/05/2011 ©Velleman nv

Connecting the mouse

• Plug the USB-mouse connector into the USB input [22] at the rear of the DVR.

Connecting external alarms / RS485

• When desired, connect external alarm inputs (e.g. from door/window contacts) to the alarm input connector

[13].

Connecting ground

• Connecting the ground terminal [14] to earth might resolve any image interference problems. Do not

connect when the image is fine.

Connecting the power supply

• Plug a DC output connector of the included power adaptor into the 12VDC power input [15] at the back of

the DVR.

WARNING: only use the included adaptor.

• Plug the included power cable into the adaptor input connector and plug the other end into the mains.

• Switch to DVR on with the ON/OFF switch [12].

Connecting Local Area Network (LAN)

• Connect the DVR to a local network by plugging a network cable into the LAN port [21] at the back of the

DVR. Connector type is 8P8C (RJ45). Setup is done through the OSD.

7. Operation

Note: the functions, navigation and options of the DVR are accessible via the front panel, the remote control

or by using the mouse.

• Switching on the DVR with the ON/OFF switch [12] at the back. It takes about 45 seconds for the

initialization to complete and to show live images.

• After start-up, the power LED [6] is on and the display shows the 4 camera channels simultaneously. Date

and time is shown in the top area of the display. Should one of the images remain blank, check the camera

and cabling of that channel.

• Press the LCD power switch [2] to switch the LCD screen on or off. This does not interrupt the recording

operation of the DVR!

Standby Mode

The system can also be put into standby mode. Power will remain to the system but recording is disabled.

To start/stop Standby mode:

• Press and hold the STANDBY button on the front panel [2] or remote control [A] until the

progress bar filled up completely. The system enters standby mode.

• Press and hold the STANDBY button on the front panel [2] or remote control [A] for ±3 seconds.

The system will power up again.

Password

ATTENTION: By default, passwords are disabled on the system. You do not need to enter a password

when accessing any system menu. However, for security purposes, it is highly recommended to

enable passwords on the system using the password menu. Refer to §7.3.4.

NOTE:

• If there is no HDD in device, or the device can’t read the HDD, or the HDD isn’t formatted, a [H] is

displayed in the video preview interface.

• The HDD in the DVR must be formatted before first use. Refer to §7.3.3.

7.1 General menu guidelines

• Enter the menu of the DVR by either pushing the MENU-button on the front panel [4] or remote control,

or click the right mouse button, select ‘MAIN MENU’ and click left.

NOTE: If passwords are enabled on the system, you need to select your Device ID and enter the 6-digit

numerical password to open the Main Menu (see §7.3.4).

7.2 Screen image

• Front panel controls:

Press the channel selector [2] repeatedly to scroll through the 4 channels or see all four channels

simultaneously.

• Remote control:

Press on a numbered channel button (1~4) to see that channel full screen. Press the button to return to

the quadruple display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Perel CCTVSET10 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info