Bedienungsanleitung Perel SCAMSETW1 (Seite 3 von 17) (Deutsch)

545394

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

SCAMSETW1 PEREL

SCAMSETW1 – PORTABLE WIRELESS VIDEO MONITORING KIT

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm

the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized

company for recycling.

This device should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for buying the SCAMSETW1! Please read the manual thoroughly before bringing this device into service. If

the device was damaged in transit, don't install or use it and contact your dealer. Contents: 1 x wireless camera, 1 x

camera base, 1 x wireless monitor, 2 x wall bracket, 4 x screw, 2 x power adapter.

2. Installation

a. The Camera

• Unpack the camera carefully.

• Remove the camera from the stand and locate the DIP switches at the back of the camera. Select camera 1, 2 or

3 by moving DIP switches 1, 2 or 3 to the down position using a sharp pencil.

• The camera can be fixed to the wall or be placed onto the desk. If the camera is to be fixed on

the wall, remove the base by sliding it from the camera as shown in the picture. Choose the

mounting location carefully and pre-drill 2 holes at a distance of 28mm and a depth of ± 12.5mm

using an appropriate drill. Slide a nylon plug into each hole and fix the wall bracket using the 2

screws. Be careful to fix the wall bracket with the curved side down. Now, slide the camera onto

the wall bracket and align.

• Slide the camera onto the stand if the camera is to be placed onto the desk.

• To power the camera, connect the power adapter to either the 12VDC input at the back of the

stand or to the female plug on the wall bracket. Plug the power adapter into the mains.

b. The Monitor

• Unpack the monitor carefully.

• The monitor can be placed onto the desk or be fixed on the wall. If the monitor is to be fixed on the wall, select

your mounting location carefully and pre-drill 2 holes in a horizontal position at a distance of 49mm from each

other using an appropriate drill. Slide a nylon plug into each hole and fix the wall bracket using the 2 screws.

• Now, select the cameras by placing the DIP switches in the correct position since the monitor can accept up to 3

cameras (DIP switch 1 = camera 1, DIP switch 2 = camera 2, DIP switch 3 = camera 3, all DIP switches in the

down position = monitor will automatically switch to next camera).

• To power the monitor, place either 4 x AAA batteries into the battery compartment respecting the polarity, use the

optional rechargeable battery pack or connect the AC adapter to the power input jack located in the battery

compartment.

• Fix the monitor onto the wall bracket.

•

The camera should be aimed accordingly to optimize viewing area.

• For best transmission, avoid installation spots surrounded by thick walls or with major obstructions

between the camera and the monitor. Avoid installing the camera or the monitor nearby a

microwave oven.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Perel SCAMSETW1 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info