Bedienungsanleitung Peruzzo Parma - 706 (Seite 8 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

807420

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ASSEMBLY AND USER INSTRUCTIONS

Whenever this product is used the following information must be

taken into consideration: the bike rack is a safe product if used

correctly, but if it is used incorrectly it can cause damages to you

and to anyone driving behind you.

1) Insert the plugs 3 in the bearing rails 4 (Fig. A).

2) Mount the tyre cradles 6 on the bike carrier bar 4 in the most suitable

positions for the dimensions of your bike and x them with the screws 7,

nuts and washers 8 (Fig. A).

3) Fix the hook 9 to the tilt mechanisms 10 (Fig. A).

4) Tilt the xing block 24 by pulling hook 9, then insert the plugs 1 in the

square bearing tubes 2 (Fig. B).

5) Mount the two tilter blocks 50 to the square bearing tubes 2 and x

them with the screws 51, washers 52 and nuts 53 (Fig. B).

6) Mounting the bike xing arch 5:

- Insert the plugs 54 in the bike xing arch 5 (Fig. C);

- Carry out the operations 1, 2 (only for art. 706/4) and 3 (Fig. C);

- Insert the xing arch 5 in the seat in the tilter blocks 50, then fasten it

with the washers 20, the knobs 19 and the nuts 55 (Fig. C).

7) Mount the rear lights 11 to the lighting board 12 and x together with

the washers and nuts 13 (Fig. D); take care not to damage the wires and

not to over-tighten the nuts as this could damage the plastic parts.

Thread the 13 pin plug through the central hole of the lighting board 12.

8) Fix the number plate frame 14 to the lighting board 12 with the screws

15 (Fig. D).

9) Fix the lighting board assembly 12 to the square tube 16 with the

screws 17, the nuts and the washers 18; make sure you thread the tilt

hook 9 into the slot provided (Fig. E).

For personal safety and to avoid damaging the vehicle we recommend 2

people mount the bike carrier.

10) Push the lever 22 upwards, to disengage it turn the wrench 23 counter

clockwise (Fig. F1).

11) Place the xing block 24 on the towball 25 (Fig. F2).

12) Close the clamping device by lowering the lever 22: at least 45 kg.

clamping force is required. (Fig. F2).

Adjustment of closing hand force

It is always necessary to make the rst adjustment when the product is

purchased. Then, every time the product is used, the clamping force must

be checked and adjusted if necessary. In order to prevent accidents and

damage it is advisable to ask a second person to assist you in this

procedure as well. After disengaging and lifting the lever 22 the second

person must hold the cycle carrier in a horizontal position. The screw 26

must be adjusted with the wrench provided 27 so that the clamping

force on the lever is increased to a minimum of 45 Kg. (Fig. F2). Make

sure that the bike rack does not rotate when the clamping device has

been locked.

ONLY FOR ART.706/4

13) Clean the parts of the bodywork that will be in contact with the straps of

the bike carrier. Attach the strap hooks 35 to the edges of the vehicle

hatch, then insert the straps in the buckles 34 (make sure the inlet

direction is correct) (Fig. G).

IMPORTANT

: Give the straps a good tug to check for tightness. Check the

tightness before starting and during the trip.

HOW TO INSTALL THE BIKE CARRIER ON

THE TOWBALL

14) Place the biggest and heaviest bike on the bike rack rst, position the

wheels in the tire cradles 6 and lean it up against the bike xing arch 5.

Secure the bike to the bike xing arch 5 with the xing strap 28 (Fig.

I1). Secure the wheels by means of the xing straps 29 (Fig. H).

POSITIONING AND FIXING THE BIKES ON

THE BIKE RACK

BIKE RACK INCLINATION

(Fig. L/M/N)

To tilt the bike rack hold it up with one hand while you pull the hook 9

with the other (Fig. L). To avoid injury or damage, this operation of

tilting the bike rack should be carried out with the help of a third

person. To close the bike rack, lift it until the tilt mechanism 10

engages completely by passing from the tilt position (Fig. M) to the

closed position (Fig. N).

15) Repeat the operations in 14 for the second, third and fourth bikes. The

second and third bikes are secured to the xing arch 5 with the xing

arms 30/31 (Fig. I1), whereas the fourth bike is secured to the third

bike with xing arm 32 (Fig. I2).

IMPORTANT

: For safe transportation of the load the bike carrier is

supplied with a strap 33 for tying all the bikes to the xing arch 5.

Check that the belt is mounted correctly by pulling on it (Fig. I1).

As well as the information described below please observe the

Conditions, suggestions and limits for use

" specied in the EC

type test certicate.

- Weight and maximum capacity of "PARMA" bike racks:

* Model 706/4 (20,61 kg.) ---> 4 bikes, max. capacity 60 kg.

* Model 706/3 (17,96 kg.) ---> 3 bikes, max. capacity 60 kg.

* Model 706/3A (16,35 kg.) ---> 3 bikes, max. capacity 60 kg.

* Model 706 (16,16 kg.) ---> 2 bikes, max. capacity 60 kg.

- Never exceed the permitted capacity of the towing hook installed. The

combined weight of the bike rack and the load must never exceed the

permitted capacity. Keep the towing hook ball surface clean from dirt

and oil.

- The driver is always responsible for the load he is transporting and

consequently he is also responsible for checking the fastenings both

before starting the trip and at regular intervals during the trip.

- Check the car manual for the specications concerning the maximum

permissible rear axle weight.

- Verify compliance with the value D (maximum load bearing capacity)

of the towball specied by the car or towball manufacturer; the value

D for the towball must be at least (760 Kg) 7.6kN; older towballs

often only specify the permissible load on the towball GA and the

total permissible load of the towing vehicle GK rather than value D; in

this case the value D can be calculated using the values specied in

the vehicle maintenance or registration booklet:

- Remove from the transported bikes children's seats, transport

baskets, rain covers or other elements that could get lost or increase

the air resistance.

- Do not carry more bikes than the number indicated for a specic

model.

- Bike parts, such as for example the handlebars or pedals, must not be

left in the normal position of use; they must be folded to avoid

dangerous projections.

- Ensure that the bike rack is tted correctly on the towing hook and

that the bikes are secured as instructed.

- The bike rack is only suitable for transporting bicycles.

ATTENTION – SAFETY REQUIREMENTS

D = x

9,81 (GA x GK)

1000 (GA + GK)

(D in [kN] / GA in [kg] / GK in [kg])

Peruzzo Parma - 706 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info