Bedienungsanleitung Pet-Mate Cat-Mate 360 (Seite 4 von 12) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

782683

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

6 7

8. Fitting Instructions (See Figs. 6 to 10)

IMPORTANT:

• Do not cut tunnel (B, Fig. 1) of cat flap.

• To check that your cat’s microchip is correctly positioned and functioning, we

strongly recommend you program the cat flap for all your cats before

installation (See Section 3). Then check the cat’s microchip operates the catch

(C, Fig. 1) when the cat’s head is pushed gently against the flap as shown

in Fig. 2.

• For UPVC / metal doors thicker than 35mm (13/8”) use a Cat Mate Cat Flap

Adapter Kit (Ref. 361).

• For UPVC / metal doors it is essential to retune the cat flap after fitting

(see below).

UPVC / Metal Doors

Doors constructed with metal panels may reduce the range of the microchip reader.

You may test for metal panels by drilling a small trial hole in the middle of the intended

cat flap location.

For correct operation it is important to ensure correct cut out size is made and

unit is retuned.

For UPVC / metal panels thicker than 35mm (13/8”) use a Cat Mate Cat Flap Adapter

Kit (available separately) with a circular cut out in accordance with Adapter Kit

instructions.

For UPVC / metal panels up to 35mm (13/8”) thick proceed as for Wooden Doors below.

After fitting, ensure the flap is tuned to the metal panel by pressing the PROGRAM

button (G) for 5 seconds until LED (A) lights. After 10 seconds press the PROGRAM

button again to complete retuning.

Wooden Doors

8.1 Place the exterior frame in desired position on panel and draw round the outside

of the tunnel section as shown in Fig. 6. We recommend the bottom of the hole

is approximately level with your pet's stomach.

8.2 Use an electric jigsaw to cut 2mm (1/16”) outside of drawn line. Be careful to

cut hole square to the door, particularly with thicker doors. Ensure frames are

free-fitting in hole.

8.3 Determine thickness of door panel.

8.4 For door panels 3mm (1/8”) - 25mm (1”) thick:

8.4.1 Position exterior frame on outside of door and mark four screw positions

(Fig. 7).

8.4.2 Remove frame and carefully drill screw clearance holes square to panel at

6mm (1/4”) diameter (Fig. 8).

8.4.3 For panels less than 17mm (5/8”) thick, cut excess liner from exteriorframe

(F) as shown in Fig. 9 with a hacksaw or plastic cutting disc.

8.4.4 Fit seal (I) to exterior frame. Position exterior frame on outside of door.

Screw interior frame to it by using 37mm (11/2”) screws. Finally, fit screw

caps (Fig. 10).

8.5 For door panels 25mm (1”) + thick:

8.5.1 Carefully drill out four holes in interior frame to allow close clearance on

screws (recommended drill 5mm (3/16”) diameter) as shown in Fig. 11.

8.5.2 Fit seal (I) to exterior frame. Screw exterior frame to outside of door using

13mm (1/2”) screws.

8.5.3 Screw interior frame to inside of door using 22mm (7/8”) screws. Finally, fit

screw caps.

Walls / Glass Panels

For easy installation you will require an adapter kit available from your cat flap supplier

or direct from Pet Mate (Product Ref. 361).

9. Troubleshooting

9.1 Cat’s microchip will not program

• Your cat’s microchip might be faulty or poorly positioned. Contact Pet Mate

Customer Services or use a Cat Mate I.D. Disc.

9.2 Red LED (A) flashing

• 1 flash every 30 seconds indicates need to replace alkaline batteries.

9.3 Flap does not open in response to programmed microchip or I.D. Disc

• Check catch (C, Fig. 1) moves freely up and down when cat’s head is pushed

gently against the flap as shown in Fig. 2.

• Check 4 WAY lock is set to permit access in the chosen direction.

• Check I.D. Disc, if used, is correctly fitted to cat's collar.

• If possible, try operation with another programmed microchip / I.D. Disc to

ascertain if there is a fault with a particular microchip / I.D. Disc.

• For UPVC / metal panels over 35mm (13/8”) thick check cat flap has been fitted

correctly with adapter kit and circular cut out.

• For UPVC / metal panels check cat flap has been retuned after fitting (See

Section 8).

• Check batteries are correctly orientated and not in need of replacement

(See Section 6).

• Check cat flap is mounted at correct height (See Section 8).

• If all else fails, remove one battery and wait a minimum of 5 minutes. Refit

battery and then check if flap functions correctly. If not perform a FACTORY

RESET (See Section 7) before reprogramming (See Section 3).

For further advice contact Pet Mate Customer Services on

+44 (0)1932 700 001

N America (936) 760 4333

or email

info@pet-mate.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pet-Mate Cat-Mate 360 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info