Bedienungsanleitung Petsafe PIF00-14288 (Seite 18 von 24) (Englisch)

770986

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

18 +1 (800) 732-2677

Wireless-to-Go

Your PetSafe® Stay & Play™ Compact Wireless Fence system is completely portable. Follow the setup procedures (Steps 1

through 4) wherever you wish to have containment of your pet. Reestablish the pet area and mark it with boundary flags so

your pet knows his boundary zone. Place the transmitter indoors at least 3 feet from large metal objects.

Note: If setting up in a metal building or vehicle, the maximum size of the pet area may be reduced. Be sure to remove

the receiver collar before removing power from the transmitter. If you want to power the transmitter from a car or other

DC source, use an inverter rated for 50 watts or more.

Troubleshooting

The transmitter

is sounding an

intermittent double

tone alarm.

• The intermittent double tone is the metal interference alarm. This alarm sounds if

the transmitter is placed too close to a metal surface. When this alarm sounds,

the transmission output is disabled and your pet is no longer being contained.

Relocate the transmitter and either unplug the power adaptor from the power

jack or press the alarm disable button for 5 seconds then release.

The transmitter is

sounding a intermittent

single tone when I

unplug the power

adaptor from the

wall outlet.

• The power loss alarm in the transmitter is activated to alert you that power has

been removed from the transmitter and your pet is no longer being contained.

To turn off the power loss alarm, unplug the power adaptor from the power jack

located on the bottom of the transmitter or press the alarm disable button for

5 seconds then release.

The transmitter is

generating a loud

continuous tone.

• The transmitter has a built in transmission failure alarm that continuously monitors

the transmitter output. If a transmission failure ever occurs the alarm warns you that

your pet is no longer being contained. Contact the Customer Care Center for a

replacement transmitter.

The receiver collar

tone is not sounding

when setting up the

boundary zone.

• Make sure the receiver collar is turned on and battery status lights are flashing

every 4-5 seconds.

• Charge receiver collar.

• The tone may be difficult to hear in a noisy environment.

• Use test light as explained in the “test light instructions” section, and use it to

determine the location of boundary zone.

• Check that the transmitter is set up according to directions.

The receiver collar

tone is not sounding or

administering a static

correction.

• Make sure receiver collar is turned on and battery status lights are flashing every

4-5 seconds.

• Charge receiver collar.

• Check that the transmitter is plugged into a working 120 volt outlet, the power light

is on, and the transmitter controls are set at your desired settings.

The receiver

collar tone is

sounding everywhere.

• Check that the transmitter is plugged into a working standard 120 volt outlet, the

power light is on, and the transmitter controls are set at your desired settings.

• Bring the receiver collar within 10 feet of the transmitter to reset.

• Make sure no continuous alarm is sounding on the transmitter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PIF00-14288 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info