Bedienungsanleitung Petsafe PIF00-15002 (Seite 8 von 24) (Englisch)

770990

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1-800-732-26778

Step 2: Prepare the Receiver Collar

Your Receiver Collar comes with short Contact Points installed. Use the Long Contact Points for

pets with long or thick hair. Tighten the Contact Points using the Contact Point Wrench (2A). Check

tightness weekly.

Insert and Remove the Receiver Collar Battery

Note: Do not install the battery while the Receiver Collar is on your pet.

This Receiver collar utilizes a replaceable PetSafe® battery (RFA-67). This unique battery is designed to

make battery replacement easier and increase water protection. Once you insert the battery and turn it

to the lock position, the unit will be turned ON.

To insert the battery, align the symbols on the battery (arrow) and Receiver Collar (triangle) (2B). Use

the edge of the Test Light Tool (2B) to turn the battery clockwise until the arrow lines up with the lock

symbol on the housing.

To remove the battery, turn the battery counter-clockwise using the edge of the Test Light Tool (2C).

DO NOT attempt to cut into or pry open the battery. Be sure to discard the used battery properly.

Risk of explosion if batteries are replaced by an incorrect type. Do not short

circuit, mix old and new batteries, dispose of in fire, or expose to water. When

batteries are stored or disposed, they must be protected from shorting. Dispose

of used batteries properly.

Note: Before replacing the battery, discharge all power by holding the Mode Button at least 30

seconds until the LED is no longer illuminated.

A replacement PetSafe® battery (RFA-67) can be found at many retailers. Contact the Customer Care

Center at 1-800-732-2677 or visit our web site at www.petsafe.net to locate a retailer near you.

Turn the Receiver Collar ON

Press and hold the Mode Button continuously for 5 seconds (2D) The green or red Receiver Indicator

Light will turn ON for 5 seconds (2E) to indicate battery status, followed by the red Receiver Indicator

Light flashing the Static Correction level settings.

Turn the Receiver Collar OFF

Press and hold the Mode Button continuously for 5 seconds. The red Receiver Indicator Light will be

ON during this time. The red Receiver Indicator Light will then turn OFF and all Receiver Indicator

Lights will stay OFF indicating that the unit is turned OFF.

Set the Static Correction Level

Read all steps before attempting to set the Static Correction Level.

1. Press the Mode Button and release (2D) when the Receiver Indicator Light illuminates Red (2E).

2. The Receiver Indicator Light will emit a series of red flashes representing the Static Correction Level.

3. Increase the Static Correction Level by pressing and releasing the Mode Button within 5 seconds

of the previous series of flashes.

The Static Correction Levels increase in strength from 1 to 6. Pushing the Mode Button while the

Receiver Collar is on Level 6 will cause the Receiver Collar to revert to Level 1. Refer to the Function

and Response Table to choose the Static Correction Level that best fits your pet.

Mode

Button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PIF00-15002 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info