Bedienungsanleitung Petsafe PIG00-11115 (Seite 6 von 19) (Englisch)

770991

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

petsafe.com1-800-732-2677 1110

Step 4: Design Your Boundary Zone

Basic Planning Tips

• Always design your layout, position the boundary wire and test

the system as outlined in this guide before burying the boundary

wire. You do not want to find out after burying the wire that there

is a problem with your layout or a loose connection somewhere.

• The boundary wire must start at the fence transmitter and make a

continuous loop back to it (4A).

• Always use gradual turns at the corners with a minimum 3 ft.

radius to produce a more consistent boundary (4B).

• Create areas in your yard that allow your pet to safely cross

over the boundary wire without static correction by twisting

the boundary wires together 10 to 12 times per foot (4G). This

transmission cancels the signal and allows your pet to safely cross

over that area. This will be explained in more detail in Step 5.

• YardMax® mode layouts need to be at least 10 ft. from

neighboring YardMax® systems.

• Cross any utility lines at a 90° angle.

• Work carefully; a nick in the wire insulation could render it

useless, or create a weak area in the signal field.

• Ensure there is at least 10 ft. between the boundary wire and any

danger zones like roadways.

Single or Double Loop Layout

The containment area can be created by using a single boundary

wire that is placed around the entire property (4C) or by doubling

the boundary wire along the same path (4D).

Single Loop Boundary (4C)

• To create a containment area for the entire property

• Used with YardMax® mode (A) or Traditional mode (B)

• For exclusion areas around gardens, landscaping or pools

(Traditional mode only)

With a single loop layout, the boundary wire starts at the fence

transmitter, advances out to the yard, continues all the way around

the perimeter of the property and connects back to the fence

transmitter. This forms a boundary zone with a single wire.

Double Loop Boundary (4D)

• To section off only one boundary area or one section of your

yard (e.g., front yard only, or waterfront property)

• Used with Traditional mode (B) only

• The 2 parallel sections of the double boundary wire must be

separated by a minimum of approximately 5 ft. from each

other in order to avoid canceling out the signal as well as provide

an adequate boundary width (4D)

• A double loop layout requires twice as much wire as a single

loop layout because it doubles back along the same path

With a double loop layout, the boundary wire starts at the fence

transmitter, advances out to the yard and continues to form a

boundary zone in one section of your property (e.g., front yard

only). Then the wire makes a U-turn back along the same path and

connects back to the fence transmitter. This forms a boundary zone

with a double wire.

5’

Single Loop

Double Loop

YardMax® Mode (A) Layouts

The YardMax® Fence system can only be used with a single

loop layout.

Sample 1(4E): Full Perimeter Loop

With a full perimeter loop, YardMax® mode allows your pet to

maximize the pet area and roam the entire property freely and safely.

Sample 2 (4F): Full Perimeter Loop Using Existing Fence

This layout allows you to include your existing fence as part of your

layout and keep your pet from jumping out or digging under your

existing fence. This layout also greatly reduces the installation time

since most of the wire will not need to be buried.

Using either sample 1 or 2, run the wire from the fence transmitter

to point A, then to point B and so on (B to C to D to E) all the way

around the entire property until back to point A again. The wires from

point A will then need to be twisted and connected back to the fence

transmitter inside your home.

Traditional Mode Layouts (Setting B)

Traditional mode can be used with either a single loop or a double

loop layout. Sample 1 (4E) and Sample 2 (4F) layouts may be also

be used in Traditional mode.

Sample 3 (4G): Perimeter Loop with Exclusion Areas

(Single Loop)

This layout allows you to keep your pet out of gardens, pools or

landscaping within your yard.

Sample 3

Wire

Splices

Place

Transmitter

Inside

Pets Can

Safely Cross

Twisted Wires

Pets Can

Safely Cross

Twisted Wires

10 Twists/ft.

Sample 1

Sample 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PIG00-11115 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info