Bedienungsanleitung Petsafe PIG00-11115 (Seite 15 von 19) (Englisch)

770991

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

petsafe.com1-800-732-2677 2928

Wire Break Location Test

The following lists identify the common locations where wire breaks occur.

Please inspect these areas for signs of damage.

Wire breaks in the twisted pair are commonly found:

1. At the wire exit point of the house

2. Where the twisted pair of wire enters the ground from the house,

usually caused by string trimmers

3. Where the wires cross sidewalks or driveways due to edging and

string trimmers

4. Around landscaping and flower beds due to digging, or working up

the soil

Wire breaks in the boundary wire are commonly found:

1. In aerated lawns

2. Where the wires cross sidewalks or driveways due to edging and

string trimmers

3. Around landscaping and flower beds due to digging, or working up

the soil

4. At wire splices where gel-filled capsules have not been installed

5. At wire splices without reinforcement knots (15A)

If you still cannot find the break in the boundary wire, there are

2 options for locating it:

Option 1: It is recommended to contact the Customer Care Center to

purchase a wire break locator (15B). The Wire Break Locator detects full

breaks, not partial breaks.

Option 2: Follow the procedure below:

1. Unplug the fence transmitter.

2. Connect both ends of your twisted boundary wire to one loop

terminal on the surge protector.

3. Measure and cut a test wire which is half the length of your total

boundary wire footage.

4. Connect one end of test wire to the other loop terminal on the

surge protector.

5. Locate the halfway point of your boundary and cut the boundary wire.

6. Splice the other end of the test wire to either side of your boundary

wire where you cut it in half.

7. Plug in the fence transmitter, set the mode to mode (B), and check the

loop indicator light. If the loop indicator light is on, you can assume that

the break is in the other half of the boundary wire.

8. If the loop indicator light did not come on, you may assume there is a

break in this portion of the boundary wire. However, there is a small

chance of having more than one break in your system. Be sure to check

both halves of your entire loop.

9. Replace the damaged boundary wire with new boundary wire.

10. Reconnect the boundary wire to the surge protector.

11. Check the loop indicator light. If the loop indicator light is on, test the

system with the receiver collar.

15 A

15 B

Receiver Collar Status Indicators

The receiver collar light and with the alarm tones are used to determine the operational mode, the battery status and the correction level. Refer

to the receiver collar status table below to understand the status lights and tones for the receiver collar. During normal operation, the receiver

collar light will flash every 4 seconds to indicate the battery status as shown in the table below. If your receiver collar has not been moved for

at least 20 seconds, the battery status light will function, but the receiver collar will enter sleep mode to conserve battery life. To wake up the

receiver collar simply pick it up and flip it over or shake it.

Receiver Collar Status Table

Light Status Alarm Tone Condition

While Plugged into the Receiver Charger

Solid red No tone Charge in progress

Solid green No tone Charge complete

No light No Tone Charge failure—contact Customer Care Center

ReadyTest® Startup

(After removing the receiver collar from the charger or after first turning it on)

Off for 1 second No tone Unit is starting the ReadyTest® startup feature

Continuous red, green, or red+green together

(5 seconds) No tone Battery charge status

Flashing red from 1 to 6 times No tone Receiver collar is reporting the

static correction level from 1 to 6

Continuous red 20 seconds ReadyTest® failure;

Unit is not operational—contact Customer Care Center

PerfectFit Test

Flashing red+green together

(every 1 second) No tone Unit is in PerfectFit mode for 90 seconds

after the ReadyTest® startup is completed

Flashing green

(every 1 second)

5 consecutive double tones

for a confirmed fit

PerfectFit mode indicates that the collar is making

true contact with the pet’s skin

Static Correction Level

Flashing red from 1 to 6 times No tone Receiver collar is reporting the

static correction level from 1 to 6

Receiver Activation Status

Fast pulsating green Warning tone Warning tone

Fast pulsating red Duration of the correction Static correction is being delivered

(up to 10 seconds)

Continuous green

(10 seconds) No tone Over Correction Protection feature;

Collar is locked for 10 seconds

Slow blinking green

(every 4 seconds) No tone Collar battery charge 100%–60%

Slow blinking red+green together

(every 4 seconds) No tone Collar battery charge 60%–20%

Slow blinking red

(every 4 seconds) No tone Collar battery charge 20% or less;

Charge immediately

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PIG00-11115 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info