Bedienungsanleitung Petsafe PIG00-11116 (Seite 7 von 19) (Englisch)

770992

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

petsafe.com1-800-732-2677 1312

Sample 4 (4H): Front Yard or Back Yard Only

(Double Loop)

From the fence transmitter, run the wire to point A, then to point B and

so on (B to C to D to E to F). Next, make a U-turn and follow your

path all the way back to point G, keeping the wire separated by at

least 5 ft. When you get back to the house (G), make a sharp turn

along the side of the house back to point A. Finally, twist the wires

from point A and connect them back to the fence transmitter.

Sample 5 (4I): Front Boundary Only

(Double Loop)

From the fence transmitter, run the wire to point A, then to point B.

Make a U-turn and follow your path back to point A, keeping the

wire separated by at least 5 ft. Then twist the wires from point A and

connect them back to the fence transmitter.

Sample 6 (4J): Waterfront Property

(Double Loop)

From the fence transmitter, run the wire to point A, then to point B.

Make a U-turn and follow your path to C, then to D, then to E. Next,

make another U-turn and follow the same path all the way back to

point A, keeping the wire separated by at least 5 ft. Finally, twist the

wires from point A and connect them back to the fence transmitter.

Sample 7 (4K): Wire Loop Attached to Existing Fence

(Double Loop)

This layout allows you to include your existing fence as part of your

layout and keep your pet from jumping out or digging under your

existing fence. It reduces the amount of wire which will need to

be buried. From the fence transmitter run the wire to point A, then

to point B and so on (B to C to D to E to F). Next, make a U-turn

and follow your path all the way back to point A, keeping the wire

separated by at least 5 ft. Finally, twist the wires from point A back to

the fence transmitter.

Place Transmitter

Inside

5’

Sample 4

Sample 5

5’

Sample 6

5’

Sample 7

5’

Step 5: Position, Twist and Splice the

Boundary Wire

Once you have designed your layout, the next step is to position the

wire along your property. Hold off on burying the wire until you have

tested the system first.

1. Start with one end of the wire at the surge protector, but do not

plug it in yet. Run the wire outdoors all the way around your

planned perimeter and back to the surge protector.

2. You will need to twist the 2 wires together for the area running

from the transmitter inside your home out to the yard so that your

pet can cross this section without a correction (5A). Twisting both

ends of the wire together 10-12 times per ft. cancels the signal.

Keep in mind that crossover areas will only work when set up

within the containment area. Straight crossover breaks along the

perimeter, such as across driveways (5B), cannot be created and

the signal will not be canceled.

Quick tip: The fastest way to twist 2 wires is to cut 2 pieces a little

longer than the length you need, twist them and then “splice” in that

section. Anchor one end of the 2 wires to something secure (or have

a partner hold them), and insert the other end into a power drill. Pull

the wire taut. Then use the drill to twist the wire quickly. Go slowly.

Follow the splicing guide below to learn how to reconnect this

twisted portion back to the main boundary wire.

Splicing Guide

Although not required, it is recommended that you cut and splice

the wire between each twisted section. Your YardMax® system

comes with 2 gel-filled splice capsules to ensure that your splices are

waterproof. You can give us a call if you would like to purchase more

splice capsules.

a. Strip approximately 3⁄8 in. of insulation off the ends of the wires

to be spliced (5C).

b. Insert the stripped ends into the wire connector and twist

the wire connector around the wires. Make sure there is no

copper exposed beyond the end of the wire connector.

c. Tie a knot 3 to 4 in. from the wire connector (5D). Ensure that the

wire connector is secure on the wire splice.

d. Once you have securely spliced the wires together, open

the lid of the gel-filled splice capsule and insert the wire

connector as deeply as possible into the waterproof gel

inside the capsule (5E).

e. Snap the lid of the capsule shut (5F).

Additional Boundary Wire

Extra spools of boundary wire can be purchased in lengths of 500

ft. per spool at the store where you purchased the kit or through the

Customer Care Center.

Note: When adding wire, it must act as a continuous loop.

The table on the right indicates the approximate length of boundary

wire needed for a square, single-loop layout. The length will vary

due to the amount of twisted wire and the layout used.

³⁄₈ in.

5D5C

5E 5F

Acres Feet of Wire Needed Number of Extra Spools Needed

1⁄4415 -

1⁄3480 -

1⁄2590 1

1835 1

2118 0 2

51870 3

10 2800 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PIG00-11116 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info