Bedienungsanleitung Petsafe PUL-275 (Seite 14 von 28) (Englisch)

770982

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

14 1-800-732-2677

Step 6: Prepare the Receiver Collar

There are two sets of contact points that can be used on your receiver collar. Your receiver collar comes with the

short contact points installed. The longer contact points should be used on dogs with long hair. Tighten the contact

points using test light tool one-half turn beyond finger tight. Check the tightness weekly.

Insert and Remove the Battery

Note: Do not install the battery while the receiver collar is on your pet.

This receiver collar utilizes a replaceable PetSafe® battery (RFA-67D-11).

This unique battery is designed to make battery replacement easier and

increase water protection.

To insert the battery, align the symbols on the battery (arrow) and receiver

collar (triangle). Use the edge of the test light tool to turn the battery

clockwise until the arrow lines up with the lock symbol on the housing (6A).

To remove the battery, turn the battery counter-clockwise using the edge

of the test light tool (6B). Do not attempt to cut into or pry open the battery.

Be sure to discard the used battery properly. The battery life will vary

depending on how often your pet tests the system and receives a static

correction Check the receiver collar every month to ensure the battery is

working properly.

If the receiver indicator light is flashing every 4 to 5 seconds, battery

replacement is required. Remove the old battery from the receiver collar.

Discharge all power by holding the correction level button down until the

LED light is no longer illuminated. Replace with a new battery.

A replacement PetSafe® battery (RFA-67D-11) can be purchased by

contacting the Customer Care Center or by visiting our website at

www.petsafe.com.

Set the Static Correction Level

1. Remove the clear plastic cover with the test light tool to expose the

correction level button (6C).

2. With the battery installed, press the correction level button and

release when the receiver indicator light turns on (6D).

3. The receiver indicator light will emit a series of flashes representing

the static correction level (e.g., 4 red flashes means level 4).

4. Increase the static correction level by pressing and releasing the

correction level button within 5 seconds of the previous series

of flashes.

5. After setting the static correction level, replace the cover to protect the

correction level button.

The static correction levels increase in strength from 2 to 5, with level 1

being tone only (no correction), and level 5 being the maximum setting.

Pressing the correction level button while the receiver collar is on level 5

will cause the receiver collar to revert to level 1. Refer to the function and

response table to choose the static correction level that best fits your pet.

The receiver collar is equipped to automatically increase the level of static

correction the longer your pet remains in the static correction zone if the

collar is set at level 2 or above.

The receiver indicator light acts as a low battery indicator, flashing every 4

to 5 seconds when replacement is required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe PUL-275 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info