Bedienungsanleitung Petsafe ZIG00-16969 (Seite 12 von 28) (Englisch)

770983

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

12 1-800-732-2677

Step 4: Position, Twist and Splice the Boundary Wire

Once you have designed your layout, the next step is to

position the wire. Hold off on burying the wire until you have

tested the system first.

• Start with one end of the wire at the transmitter, but do

not turn it on yet. Run the wire all the way around your

planned perimeter and back to the transmitter.

Off-limits Areas

• For off-limits areas like gardens, you will need to splice a

section between the main boundary wire and the off-limits

area (3C). This will allow your pet to cross this section

without a correction.

• Also, keep in mind that if you plan to mount the transmitter

to a post or you decide to place it away from the main

boundary location, the boundary wire that runs from

the transmitter out to the main boundary must also be

twisted together.

• Twisting both ends of the wire together 10-12 times

per foot cancels the signal and allows your pet to cross

without receiving a correction. Any crossover areas

must be within the boundary and cannot be along the

perimeter of the boundary (4A). Although not required, it

is recommended that you cut and splice the wire between

each twisted section.

• The fastest way to twist 2 wires is to cut 2 pieces a little

longer than the length you need, twist them, and then

“splice” in that section. Anchor one end of the 2 wires to

something secure (or have a partner hold them), and insert

the other end into a power drill. Pull the wire tight and then

use the drill to slowly twist the wire. Follow the splicing

guide below to learn how to reconnect this twisted portion

back to the main boundary wire.

Splicing Guide

Your system comes with 2 gel-filled splice capsules to ensure

that your splices are waterproof. Contact us if you would like to

purchase more splice capsules.

1. Strip approximately 3⁄8 in. of insulation off the ends of the wires to be spliced (4B).

2. Insert the stripped ends into the wire connector and twist the wire connector around the wires. Make sure

there is no copper exposed beyond the end of the wire connector.

3. Tie a knot 3 to 4 in. from the wire connector (4C). Ensure that the wire connector is secure on the wire splice.

4. Once you have securely spliced the wires together, open the lid of the gel-filled capsule and insert the wire

connector as deeply as possible into the waterproof gel inside the capsule (4D).

5. Snap the lid of the capsule shut (4E).

Additional Boundary Wire

Extra spools of boundary wire can be purchased in lengths of

500 ft. per spool where you purchased the kit or through the

Customer Care Center.

Note: When adding boundary wire, it must act as a

continuous loop.

The table on the right indicates the approximate length of

boundary wire needed for a square, single loop layout. The

length will vary due to the amount of twisted wire and the

layout used.

}

³⁄₈ in. ³⁄₈ in.

4B 4C

4D 4E

Acres Feet of wire required

1⁄4415

1⁄3480

1⁄2590

1835

2118 0

51870

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Petsafe ZIG00-16969 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info