Bedienungsanleitung Philco TB100HH9 (Seite 26 von 32) (Englisch)

492068

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1A23

OTHERS

Troubleshooting

Before requesting service for this STB, check the table below for a possible cause of the problem you are

experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore

proper operation.

Symptom Remedy

No power

• Make sure that the AC power cord is securely plugged into the power outlet.

• Make sure that the POWER indicator is lit.

The STB is not

responding to the remote

control

• Make sure to point the remote control at the remote control sensor.

• You may be too far from STB. Try moving closer.

• Remove any obstacles between the remote control and the remote control

sensor.

• Make sure that the batteries are installed in the correct direction (+ and –).

• The batteries may be depleted. Replace them with new ones.

No picture

• Make sure that the video cable is correctly connected.

• Make sure that video devices (TV or monitor) are turned on.

• Make sure that video devices (TV or monitor) are correctly set to STB video

output channel. Refer to your TV’s manual for further information.

• Check the video cable.

• Check the antenna and the RF cable. There may be damage or interfering

sources.

Blocked noise on picture

• There may be interfering sources.

No EPG or the provided

information is wrong

• Make sure that “DST” and “TIME ZONE” is set correctly in “TIME” menu

or in “SETUP WIZARD”.

No sound

• Make sure that the audio cable is correctly connected.

• Make sure that audio devices (stereo, TV or decoder) are turned on.

• Make sure that audio devices (stereo or decoder) are correctly set to STB

audio output channel.

• When TV has only one audio input jack, use a standard audio cable (white)

to connect the audio output jack (white) on STB to the audio input jack on

the TV.

Low volume

• Sound volume differs depending on the audio out setting. Select “RF OUT”

at step 5 in the “Setup Wizard” on page 13 if you feel the volume is too low.

No reception

• Make sure to complete autoscan in “SETUP WIZARD” or in “SETUP”

menu. It will be required when you setup STB for the first time or when

STB is moved to a location where other channels are broadcast.

• The selected channel does not exist at that time. There are not always sub-

channels being broadcast.

• When autoscan is interrupted and not completed, some channels will not be

received.

The entered channel

number changes

automatically

• Many digital channels have alternate channel numbers. STB changes the

numbers automatically to the ones signifying the broadcasting stations.

No reception of channels

with weak signal

(autoscan)

• Some channels with weak signal may not be received properly. This is

not a malfunction.

X6032UD_Book.indb 26X6032UD_Book.indb 26 11/28/2007 4:34:47 PM11/28/2007 4:34:47 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philco TB100HH9 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info