Bedienungsanleitung Philips 20PV184 (Seite 4 von 12) (Englisch)

33199

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Important for the United Kingdom

This apparatus is fitted with an approved moulded 13 Amp

plug. To change a fuse in this type of plug proceed as follows:

1 Remove fuse cover and fuse.

2 Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI

approved type.

3 Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should

be cut off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of

5A. If a plug without a fuse is used, the fuse at the distribution

board should not be greater than 5A.

Note: * The severed plug must be destroyed to avoid a

possible shock hazard should it be inserted into a 13A

socket elsewhere.

How to connect a plug:

The wires in the mains lead are coloured in accordance with

the following code:

BLUE - ’NEUTRAL’ (’N’)

BROWN - ’LIVE’ (’L’)

1 The BLUE wire must be connected to the terminal which is

marked with the letter ’N’ or coloured BLACK.

2 The BROWN wire must be connected to the terminal

which is marked with the letter ’L’ or coloured RED.

3 Do not connect either wires to the earth terminal in the

plug which is marked with the letter ’E’ or by the safety

earth symbol

or coloured green or green-and-

yellow.

Before replacing the plug cover, make certain that the cord

grip is clamped over the sheath of the lead - not simply over

the two wires.

Connecting the cables

1 Insert the aerial plug into the

socket.

2 Insert the plug of the mains cable into the wall socket.

3 Switch the set on. The power switch

is located on

the left side panel of the set.

Important notes for operation

• We advise you, from now on, to switch the set to standby

using the

STANDBY m

button on the front of the set or on

the remote control.

• When the set is in the standby mode, a small red lamp on

the left of the front of the set will be alight.

• You can switch on with the

STOP h

button, the

0-9

buttons or by inserting a cassette.

• Attention: When you use the power switch

on the

side panel, you have completely switched off the set from

the mains power supply. No programmed recordings will

then be made. The red lamp on the left of the front of the

set will not be alight. After a few hours, the date and clock

settings will be lost.

• Attention: Before you switch off the appliance with the

power switch

, remove the tape by pressing the

button.

• Keep your TV Combi connected to the mains and the

power switch in ’on’ position at all times to ensure that

programmed recordings can be made and that the

television functions normally. The power consumption

required is low.

• Back-up power supply: TV channel storage - typically 1

year, Clock/Timer - typically 30 hours.

1. INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 20PV184 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 20PV184

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info