Bedienungsanleitung Philips 220S4L (Seite 33 von 36) (Englisch)

514610

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

8. Troubleshooting & FAQs

• Eliminate the vertical bars using the Phase/

Clock of Setup in OSD Main Controls. It is

valid only in VGA mode.

Image appears blurred, indistinct or too dark

• Adjust the contrast and brightness on

On-Screen Display.

An "after-image", "burn-in" or "ghost image"

remains after the power has been turned off.

• Uninterrupted display of still or static

images over an extended period may cause

"burn in", also known as "after-imaging "

or "ghost imaging", on your screen. "Burn-

in", "after-imaging", or "ghost imaging" is a

well-known phenomenon in LCD panel

technology. In most cases, the "burned in"

or "after-imaging" or "ghost imaging" will

disappear gradually over a period of time

after the power has been switched off.

• Always activate a moving screen saver

program when you leave your monitor

unattended.

• Always activate a periodic screen refresh

application if your LCD monitor will display

unchanging static content.

• Failure to activate a screen saver, or a

periodic screen refresh application may

result in severe “burn-in” or “after-image”

or “ghost image” symptoms that will not

disappear and cannot be repaired. The

damage mentioned above is not covered

under your warranty.

Image appears distorted. Text is fuzzy or

blurred.

• Set the PC’s display resolution to the same

mode as monitor’s recommended screen

native resolution.

Green, red, blue, dark, and white dots appears

on the screen

• The remaining dots are normal

characteristic of the liquid crystal used in

today’s technology, Please refer the pixel

policy for more detail.

The "power on" light is too strong and is

disturbing

• You can adjust “power on” light using the

power LED Setup in OSD main Controls.

For further assistance, refer to the Consumer

Information Centers list and contact Philips

customer service representative.

8.2 General FAQs

Q1: WhenIinstallmymonitorwhatshould

I do if the screen shows 'Cannot

display this video mode'?

Ans.: Recommended resolution for this

monitor: 1680 x 1050 @ 60 Hz.

• Unplug all cables, then connect your PC to

the monitor that you used previously.

• In the Windows Start Menu, select Settings/

Control Panel. In the Control Panel

Window, select the Display icon. Inside the

Display Control Panel, select the 'Settings'

tab. Under the setting tab, in box labelled

'desktop area', move the sidebar to 1680 x

1050 pixels.

• Open 'Advanced Properties' and set the

Refresh Rate to 60 Hz, then click OK.

• Restart your computer and repeat step 2

and 3 to verify that your PC is set at 1680

x 1050 @ 60 Hz.

• Shut down your computer, disconnect your

old monitor and reconnect your Philips

LCD monitor.

• Turn on your monitor and then turn on

your PC.

Q2: Whatistherecommendedrefresh

rate for LCD monitor?

Ans.: Recommended refresh rate in LCD

monitors is 60 Hz, In case of any

disturbance on screen, you can set it

up to 75 Hz to see if that removes the

disturbance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 220S4L Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 220S4L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info