Bedienungsanleitung Philips 223S7 (Seite 4 von 29) (Englisch)

666017

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

1. Important

• Reposition your screen to

appropriate height and angle

according to your height.

• Adjusting the brightness and

contrast to appropriate level.

• Adjusting the environment

lighting similar to that of your

screen brightness, avoid the

fluorescent lighting, and surfaces

that don't reflect too much light.

• Seeing a doctor if your symp-

toms.

Maintenance

• To protect your monitor from

possible damage, do not put

excessive pressure on the LCD

panel. When moving your monitor,

grasp the frame to lift; do not lift

the monitor by placing your hand or

fingers on the LCD panel.

• Unplug the monitor if you are not

going to use it for an extensive

period of time.

• Unplug the monitor if you need to

clean it with a slightly damp cloth.

The screen may be wiped with a

dry cloth when the power is off.

However, never use organic solvent,

such as, alcohol, or ammonia-based

liquids to clean your monitor.

• To avoid the risk of shock or

permanent damage to the set, do

not expose the monitor to dust,

rain, water, or excessive moisture

environment.

• If your monitor gets wet, wipe it

with dry cloth as soon as possible.

• If foreign substance or water gets in

your monitor, please turn the power

off immediately and disconnect

the power cord. Then, remove the

foreign substance or water, and

send it to the maintenance center.

• Do not store or use the monitor in

locations exposed to heat, direct

sunlight or extreme cold.

• In order to maintain the best

performance of your monitor and

use it for a longer lifetime, please

use the monitor in a location

that falls within the following

temperature and humidity ranges.

• Temperature: 0-40°C 32-104°F

• Humidity: 20-80% RH

Important information for Burn-in/

Ghost image

• Always activate a moving screen

saver program when you leave

your monitor unattended. Always

activate a periodic screen refresh

application if your monitor will

display unchanging static content.

Uninterrupted display of still or

static images over an extended

period may cause “burn in”, also

known as “after-imaging” or “ghost

imaging”, on your screen.

• “Burn-in”, “after-imaging”, or

“ghost imaging” is a well-known

phenomenon in LCD panel

technology. In most cases, the

“burned in” or “after-imaging” or

“ghost imaging” will disappear

gradually over a period of time after

the power has been switched off.

Warning

Failure to activate a screen saver, or

a periodic screen refresh application

may result in severe “burn-in” or “after-

image” or “ghost image” symptoms

that will not disappear and cannot be

repaired. The damage mentioned above

is not covered under your warranty.

Service

• The casing cover should be opened

only by qualified service personnel.

• If there is any need for any

document for repair or integration,

please contact with your local

service center. (please refer to the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 223S7 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 223S7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info