Bedienungsanleitung Philips 24PFS6805 (Seite 58 von 71) (Englisch)

743274

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

press OK.

 (Home) > Settings > All

settings > Picture > Picture style

• Restore picture style, select back to Picture style,

then press  Restore style.

• Reset all TV settings, go

to  (Home) > Settings > All settings > General

settings > Reinstall TV.

• Check the connections of the source/input devices.

Poor reception

If the TV picture is distorted or variable in quality, the

input signal might be poor. A weak digital signal is

seen as a picture that is breaking up in square blocks

and freezes occasionally. Much sooner than a bad

analogue signal, a bad digital signal will fall away.

• Check if the antenna cable is properly connected.

• Large loudspeakers, unearthed audio devices, neon

lights, high buildings and other large objects can

influence reception quality when you are using an

antenna. Try to improve the reception by changing

the antenna direction or moving devices away from

the TV. Bad weather might deteriorate the reception.

• Check if all connections, to and from your devices,

are properly connected.

• If reception on only one channel is poor, fine-tune

this channel with Analogue: manual installation. (Only

for analogue channels)

 (Home) > Settings > Install

Channels > Antenna/cable

installlation > Analogue: manual installation

• Check if the incoming digital signal is sufficiently

strong. While watching a digital channel,

press  OPTIONS and select Status and

press OK. Check the Signal strenght and Signal

quality.

Poor picture from a device

• Make sure that the device is connected properly.

Make sure that the device's output video setting is the

highest possible resolution if applicable.

• Restore picture style or change to another picture

style.

Picture settings change after a while

Make sure that Location is set to Home . You can

change and save settings in this mode.

 (Home) > Settings > All settings > General

settings > Location

A banner appears

If an on screen promotion banner appears

occasionally or the Picture style automatically

switches back to Vivid at startup, the TV is in Shop

location. Set the TV to Home location for use at

home.

 (Home) > Settings > All settings > General

settings > Location

Picture does not fit the screen / Wrong or unstable

picture size / Picture position is incorrect

• If the picture size - its aspect ratio - does not fit the

screen, with black bars on the top and bottom or left

and right side of the screen, press  (Home) >

Settings > All settings > Picture > Picture Format >

Fill screen.

• If the picture size changes all the

time, press  (Home) > Settings > All settings >

Picture > Picture Format > Fit to screen.

• If the position of the picture is incorrect on the

screen, try to check the signal resolution and output

type of the connected device,

press  (Home) > Settings > All settings >

Picture > Picture Format > Original.

Computer picture is not stable

Make sure that your PC uses the supported resolution

and refresh rate.

 (Home) > Settings > All settings > Picture >

22.7

Sound

No sound or poor sound quality

• Check if the sound settings of the TV are OK, press

the  volume or  mute key.

• If you use a digital receiver (set-top box), check if

the volume on this receiver is not set to zero or mute.

• Check if the TV - the audio signal - is properly

connected with the Home Theatre System, if you use

such a system for the TV sound. Check if you

connected the HDMI cable to an HDMI1

ARC connection on the Home Theatre System.

• Make sure that the TV audio output is connected to

the audio input on the Home Theatre System.

Sound should be heard from the HTS (Home Theatre

System) speakers.

Sound with loud noise

If you watch a video from a plugged in USB flash drive

or connected computer, the sound from your Home

Theatre System might be distorted. This noise is heard

when the audio or video file has DTS sound but the

Home Theatre System has no DTS sound processing.

You can fix this by setting the Digital out format of

the TV to Stereo.

Press  (Home) > Settings > All

settings > Sound > Advanced > Digital out format

22.8

HDMI

• Note that HDCP (High-bandwidth Digital Content

Protection) support can delay the time taken for a TV

to display content from an HDMI device.

• If the TV does not recognise the HDMI device and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 24PFS6805 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips 24PFS6805

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info