Bedienungsanleitung Philips 28pw9615 (Seite 4 von 39) (Englisch)

145586

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

Preparation

Surround loudspeakers

There are two surround loudspeakers supplied. One is the active loudspeaker,

including the RF receiver, a power switch, the mains supply, a channel selector,

a red and black connector clip, a left/right surround loudspeaker switch and a

3.5 mm stereo jack to make a wired connection with your TV in case there is

interference or the wireless connection is not possible.The other

loudspeaker is a passive one which has to be connected with the active

loudspeaker with the supplied speaker cable.

• Set the slide channel switch 1 at the bottom of the active loudspeaker to

channel 1. (In the factory channel 1 has been chosen as the default channel.)

See also Sound Setup, p. 10.

• Connect the active to the passive loudspeaker with the supplied speaker

cable 2.

Push the connector clip down, insert one end of the colour coded wire into

the opening of one connector clip and push it up again. Insert the other end

of the same colour coded wire in the same colour connector clip of the

other loudspeaker. Do the same with the other wire in the other connector

clips. Do not insert the wires too far.

• The Surround sound loudspeakers should always be located behind or to

either side of the listener. If preferred you can also hang the loudspeakers on

the wall.

The maximum distance between the TV and the surround speakers should

not exceed 15 m.

Note: people moving around close to the TV may interfere with the sound

transmission.

• Set the slide switch 3 to the right if the active loudspeaker is positioned to

the right side of the listener, to the left if it is positioned to the left side of

the listener (seen from the point of view of watching the TV).

• Connect the active loudspeaker to the mains with the mains cable 4.

• Switch on the active loudspeaker with the POWER switch 5.

The red indicator at the front of the active surround speaker shows that the

speaker is in standby.

During sound transmission the indicator turns to green and back to red after

10-15 min. after the TV has been switched off.

To switch the active speaker off, use the

POWER switch.

( Insert the mains plug of the TV in the wall socket having a mains voltage

of 220V-240V.

To prevent damaging the mains (AC) cord which could cause a fire or electric

shock, do not place the TV on the cord.

§ Switch the TV on : Press the power switch A on the front of your TV.

A green indicator on the front of the TV lights up and the screen comes on.

If the indicator is red, press the

-P+

keys on the remote control.

The green lamp blinks every time you press a key on the remote control.

When you switch on your set for the first time, the menu

LANGUAGE

automatically appears on the screen. The explanation appears in different languages

one at a time. Choose your own language and press the OK key on the remote

control.

4934.3 gb /05 12-01-2000 14:37 Page 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips 28pw9615 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info